Use And Maintenance - Baron 700 seire Aufstellung, Gebrauchs- Und Instandhaltungs Anweisungen

Data Emissione 22/10/2004
6.3 Main burner of the cook top (open burners)
Remove the knobs and the control board, besides the grates, the
fire caps and burner heads. Unscrew the gas pipe reaching the
nozzle support. Unscrew the two screws fixing the pilot burner to the
body of the main burner, from above. Unscrew the 3 screws
fastening the burner to the cook top. Extract the burner from the
front of the equipment.
6.4 Thermocouple, pilot burner and ignition plugs of the cook top
(open burners)
Remove the knobs and the control board, besides the grates, the
fire caps and burner heads. Replace the component.
6.5 Operating thermostat of the oven
Remove the vertical control board of the oven. Unscrew the element
fastening the bulb onto the top of the cooking compartment. Extract
the capillary tube and the bulb from the outer side of the same
compartment. Disconnect the wiring of this component. Extract the
knob of the operating thermostat. Unloose the screws fastening the
thermostat to its support.
Replace the component and reassemble carrying out the same
operations backwards.
6.6 Safety thermostat of the oven
Before enabling the thermostat again, eliminate the reasons
provoking the overheating: examine the functioning of the operating
thermostat, the resistors, etc... Then carry out the following
operations: Remove the vertical control board of the oven. Press the
red pushbutton of the thermostat. Check whether the circuit is
closed again.
Replace the component operating as follows: remove the vertical
control board of the oven. Unscrew the element fastening the bulb
onto the top of the cooking compartment. Extract the capillary
from the outer side of the cooking compartment. Disconnect the
wiring of this component. Remove the screws fastening the
thermostat to its support. Replace the component and reassemble
carrying out the same operations backwards.
6.7 Switch, warning lights of the oven
Remove the vertical control board of the oven. Disconnect the wiring
of this component. Extract the knob of the switch to be replaced,
and remove the screws fixing it to the control board. Replace the
component and reassemble carrying out the same operations
backwards.
6.8 Electric resistors of the oven
Replace the fore top resistor carrying out the following operations:
Remove the vertical control board of the oven. Disconnect the
concerned resistor working in the space behind the control board.
Remove the screws fastening the concerned resistor, inside the
cooking compartment. Extract and replace the component. As
regards the other resistors, their replacement is developed as
follows:
Remove the screws fastening the concerned resistor, inside the
cooking compartment. Extract the resistor to the inside of the
cooking compartment, taking care of the electrical connections.
Disconnect the resistor, replace it, connect the new resistor and
reassemble it assuring that the electric cables are inserted in their
own original position.

7 - USE AND MAINTENANCE

7.1 Warning
This equipment has been designed for professional aims, therefore
it must be operated exclusively by trained personnel.
It must exclusively be used to cook food; consequently any other
use is improper. Its installation and possible transformation for other
gas group must be carried out by authorized and qualified installers.
In case of troubles, turn off the gas cutoff cock installed before the
equipment. For any repair, call the authorized After-Sales Service
and require only original spare parts.
Not complying with these instructions may seriously
compromise the safety of this equipment; the manufacturer
declines any liability in case these warnings are not complied
with.
7.2 Use of solid top and open burners
The knob MR controlling the cocks of the cook top is marked with
the following symbols:
Off
Pilot burner on
Maximum fire
Minimum fire
7.3 Lighting the burners of solid top and open burners (fig. 3)
Press and turn the knob MR to the position
pressing the button PA of the piezoelectric lighter (only in the solid
top, the pilot flame of open burners is lit manually, for instance, with
a match). After lighting, keep the knob pressed for approximately 20
seconds, then release it. In case of extinction of the pilot burner,
repeat this operation.
The pilot burner can be checked through the sight glass of the
control board. In emergency cases, light the pilot burner manually
approaching a flame and keeping the knob in the position . Turn the
knob to the desired position chosen between
7.4 Extinction of burners of solid top and open burners (fig. 3)
Put off the main burner turning the knob MR to the position
Put off the pilot burner pressing and turning the knob to the position
.
7.5 Use of the electric oven (fig. 3)
Safety devices - The oven is equipped with a safety three-pole
thermostat of manual reset. When the cooking compartment is
overheated, this element is enabled and disconnects the power
supply from the heating resistors. The yellow LED is off, whereas
the green one is kept on. In this case, disconnect the equipment
turning the knobs MT and ME to 0, cut off the power supply turning
off the main switch, installed before the equipment, and call the
after-sales service. This oven is equipped with 2 control knobs and
2 LEDs - warning lights (fig. 3). Knob of the main switch / thermostat
MT, for controlling the cooking temperature. Knob of the energy
controller ME, for controlling the energy sent to the top resistors of
the cooking compartment. Green warning light (LED) indicating
"current on". Yellow warning light (LED) indicating "heating on".
17
Revisione 0.0
. Light the pilot burner
and .
.