Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
In start up
Once the filter system has been properly assembled, the sand
chamber filled with sand and the hoses connected as described
above, you may begin with filtration. However, we recommend that
you clean and prepare the new sand that is in the sand chamber
first.
Cleaning the sand prior to filtering your pool will remove most of
the dust and tiny sand particles that may exist in the
move straight to filtering, these particles will end up in your
clean the sand, please follow the instructions below.
Do not plug the system in until advised to do so below.
1)
Make certain the pump is not plugged in to a power supply.
2)
Start with the valve in the 5 Closed position.
If you haven't done so already, fill your pool with
3)
that the water level is at least 2,5 – 5 cm above the top of the hose
intake
(Skimmer)
and return ports in the pool.
4)
Release the shut off valve at the intake port
pool.
If you plugged the intake port (Skimmer), remove the plug to
allow the water to flow into the intake hose.
5)
With the filter-pump system installed in a location level lower
pool's water level – water will automatically flow into the
than your
pump-filter
system.
6)
Allow the filter tank to fill with water.
7)
Check for leaks and make any necessary adjustments. Be-
cause of tolerances (in consequence of the production process), it
is possible that it may be necessary to use a Teflon tape addtition-
ally which has to be wrapped around the connections, before the
connection tube is fixed, in order to correct these tolerances.
8)
Follow the backwash process described below.
Backwash Prozess
S Disconnect the Motor/Pump from the Power Source.
Attach backwash hose (not included) to backwash port.
Place the Multi-Port Valve in the "4 - Backwash" position.
Reconnect to power source.
Run filter in BACKWASH mode until discharge water is clear.
Disconnect the Motor/Pump from the Power Source.
Place the Multi-Port Valve in the "2 - RINSE" position.
It is important that you read and follow the instructions on proper
power supply sources.
Reconnect to power source.
Allow filter to run for 60 seconds to remove any remaining residue
from pump and valve.
Disconnect the Motor/Pump from the Power Source.
Place the Multi-Port Valve in the "1 - Filtration" position.
Reconnect to power source.
Your filtration system is RUNNING and ready for further operation.
To winterize the system
1) Unplug the pump from the power source.
2) Close the shut off valves or block the flow of water at the
pool inlet and
return ports.
3) Disconnect the filtration system from the pool, drain the
tank and hoses.
4) Place the handle on the central valve in position 7- 'Winter-
ize' to relieve the
tension on the spring and internal valve
components.
Sandfilter Speedclean 75/50 | 2013_V1
Malfunction
sand.
If you
pool.
To
Pressure
gauge
reading over 1
bar
Pressure is too
low
Air in the pump
water.
Ensure
Leaking filter
(Skimmer)
in the
Pump does not
run
Sand in Pool
Air in system
Important note:
On the pump label of your filter pump is a serial number (B/...) indi-
cated and on the tank cover is a lot number shown (read from above
on handle), please provide this data in the case of a complaint.
Steinbach VertriebsgmbH,
Aistingerstrasse 2, 4311 Schwertberg, Österreich
FR/IT/CZ/HU/HR/SK/SLO/RO/BG/TR: +43 (0) 7262 / 61431-0
e-mail: service@steinbach.at
www.steinbach.at
5) Store the filter system in a location protected from frost and
severely cold temperatures.
age shed is
recommended.
Troubleshooting
Cause
Dirty filter bed
has
Hair and lint strainer
basket is dirty; Pump
gets too little water
Poor seal on the in-
take
side
of
the
pump.
Seal Defective
Not plugged in
G.F.C.I/ or main cir-
cuit breaker tripped
Pump motor defecti-
ve
If the sand is newly
replaced, the under-
sized grains are still
present
Sand
in
Central
Valve
(from
back-
wash)
Separation wall in fil-
ter is improperly in-
stalled
Filter bottom strainer
is damaged
In a garage or insulated stor-
Solution
Backwash the filter (posi-
tion 4)
Clean the hair and lint
strainer; check the suction
line and the water level
Tighten hose clamps and
connecting fittings.
Check the seal, replace if
needed
Check the socket and
power cord
Switch on the breaker (if it
is
immediately
tripped
again, there is a defect in
pump or controls)
Replace the entire pump
Backwash several times
until the backwash water
is clear (position 4)
Purge into drainpipe for
30 seconds (position 6)
Check the separation wall
for proper positioning
Replace the filter bottom
strainer
Loosen, but do not re-
move, the transparency
cover on the filter tank to
allow any trapped air to
escape. Tighten the cover
once all of the air has es-
caped
Page 9 of 35
Werbung
