Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
Resultant Damages
We cannot be responsible for damages to the product if the product
is not used in accordance with the instructions provided.
Technical Data:
Speedclean Comfort
6,6 m³/h – 0,4 bar
Flow Volume (Q)
MAX Operating Pressure
Filtration Area
Rated Voltage
230V 1N~ AC 50Hz
Power
Protection Class
Max. ambient temperature
Sand Volume
Unpacking your filter system
Carefully remove the product and all component parts from the box.
Cross reference all parts in the box with the parts list reference chart
to make certain all parts are present before beginning assembly.
NOTE: Some parts may be located within the filter tank. To access
these parts you must remove the tank cover.
Refer to Appendix A for a complete EXPLODED VIEW PARTS
DIAGRAM
Power source Instructions
The filter pump system you have purchase is equipped with a stand-
ard electrical cord and plug which should only be connected to a
power outlet protected by a qualified Ground –Fault-Circuit-
≤ 30mA that has been installed by a pro-
Interrupter (GFCI) with I
ΔN
fessional electrician and adheres to local codes and regulations.
Electrical installations should be carried out, taking the safety zone
into consideration, by a locally licensed electrician to the relevant na-
tional specifications for swimming pool construction (in Austria, EN1,
part 4, §49; in Germany, DIN 57100, Part 702 and VDE 0100, Part
702). To avoid electric shock, power cord extensions should not be
used.
Filter- Pump Assembly (Picture 1 – 5)
1. Water Pump – Base Plate Assembly
a) Secure water pump to the base plate
mounting hardware. Orient as
2. Pump Fittings Assembly
a) Screw the 1¼"-1½" hose connector
water pump. Ensure that the O-ring "A" is installed between the
port and the connector.
b) Remove the threaded ring (Collar) on
pump.
Place O-ring "B" in the grove around the hair and lint strainer bas-
c)
ket.
d) Place the transparent hair & lint strainer cover
screw the threaded ring (Collar) back on securely over the cover.
Sandfilter Speedclean 75/50 | 2013_V1
Speedclean
50
Comfort 75
8 m³/h – 0,4
bar
1,5 bar
1,5 bar
0,13 m²
0,13 m²
230V 1N~ AC
50Hz
450 Watt
550 Watt
IP X5
IP X5
35 °C
35 °C
15 kg
25 kg
with the provided pump
shown.
into the center port of the
the outer opening of the
in place and then
Insert O-ring "C"
(1 1/4")
e)
inside the outward facing opening of the
transparent hair & lint strainer cover.
Place the base plate and pump in the location where the Pump-
Filter
System will be located for normal operation and within reach
of the pool filter and return hoses but with a sufficient safety mar-
gin from the edge of the pool
Attach the filter tank to the base plate as shown.The feet on the bot-
tom of the filter tank fit within the holes provided on the base plate
Insert the tank separator plate inside the main tank in the guides
provided.
(Model Speedclean
Filling sand chamber with sand (Picture 6)
Position the filter pump assembly to the location you have dedicated
for its operation.
NOTE: Do this before you fill the chamber with sand
as the unit will become heavy and difficult to move around.
Check to ensure that the bottom strainer is correctly positioned.
Check to ensure that the tank separator plate is seated properly.
Fill the sand chamber half full with water.
Pour Quartz Sand with a particle size of 0,40 – 0,80mm into the
SAND FILTER CHAMBER being careful not to allow any sand to en-
ter the FILTERED WATER CHAMBER (see figure).
Speedclean Comfort 50 requires 15 kg of Quartz Sand with a par-
ticle size of 0,4 – 0,8mm.
Speedclean Comfort 75 requires 25 kg of Quartz Sand with a parti-
cle size of 0,4 – 0,8mm.
Securing filter assembly (Abbildung 7,8)
Ensure the main tank seal around the top of the filter tank is in good
condition and securely seated in the
sand.
Locate the upper distributor and press it into the center hole located
under the tank cover. If you are assembling Speedclean
the upper distributor will already be in place.
Carefully place the tank cover onto the filter
should be oriented so that the notch on the cover is aligned with the
matching tab on the filter tank – this ensures proper alignment.
Secure tank cover and filter tank with the tank cover lock ring as-
sembly and tighten with the knob and bolt.
Hooking up the hoses (Picture 9,10,11)
Connecting the filter system
This pool filter system is designed to connect to pools with standard
1¼ or 1½" diameter hose connectors. The type Speedclean Comfort
75 has a 2 ¼"
(Ø 32 mm or 38 mm)
your pool has a hose connector size and/or type different than de-
scribed here, you may need to purchase an adapter at your local
pool supply store or hardware retailer.
Since the hoses utilized for filtration and return lines differ for various
types of above-ground pools, the pool-filter connection section is
broken down by pool hose size and type.
Before you begin to connect hoses to the filter and pump, make cer-
tain that no water can flow through the intake or return hoses con-
nected to the pool. Some pools have shut off valves in their intake
and return ports, others do not. If you do not have a shut off valve,
block the ports with a removable plug to prevent water from passing
into and through the hoses.
Comfort
50 only)
grove.
Be sure grove is free of
Comfort
tank.
The tank cover
hose adapter for Intex® pools. If
Page 7 of 35
75,
Werbung
