Technical Data; Troubleshooting; Electrical Connection - Steinbach Active Balls 50 Bedienungsanleitung

Assembly
Filter and pump set up (Figures 1 – 12)
Fill the fi lter container with fi lter balls
Fill the fi lter container with the recommended amount of fi lter balls (Ac-
tive Balls 50 - approx. 545g, Active Balls 75 - approx. 1,150g). A pack
contains 700g of Filter Balls.
Assembling the fi lter (Figures 1 – 4)
Make sure that the seal on the upper edge of the fi lter container is
clean and in perfect condition. Put the fi lter cover carefully onto the fi lter
container. The cover should be turned so that the notch on the cover ex-
actly matches the notch on the fi lter container. This guarantees that the
cover is correctly aligned. Secure the fi lter cover with the clamping ring
provided for this purpose and tighten it with a screw and rotary knob.
Connecting the hoses (Figures 8,9)
Before starting with the connection to the fi lter or pump, make sure
there is no water fl owing from the inlet pipe or discharge pipe to your
pool.
Pools with inserted hoses having a diameter of 1 ¼" or 1 ½"
The following instructions assume that your pool is fully set up and
equipped with an inlet and drain hose. Make sure that all hose con-
nections are fi tted tightly and that none of the hoses are bent or have
several bends.
Starting up the fi lter system
When the fi lter system is completely assembled, Filter Balls have been
poured into the fi lter chamber and all hoses have been connected, you
can carry on with the initial start-up.
Do not turn on the power until this is expressly mentioned.
■ Make sure that the power cord (electric cable) of the pump is
unplugged.
■ Before operating the fi lter system, it is important to ensure that the
fi lter system is positioned outside the pool and is lower than the pool's
water level. The hose connections must also be correctly connected
and fastened.
■ If your pool is not fi lled yet, fi ll it with water. Make sure that the water
level of the pool is at least 2.5 to 5 cm above the opening of the fi lling
nozzle (skimmer).
■ Open the shut-off valve on the fi lling nozzle (skimmer) of the pool. If
you have closed the fi lling nozzle (skimmer) with a plug, remove it
now.
■ As the location of the fi lter system is lower than the water level of the
pool, the fi lter system now automatically fi lls with water.
■ The fi lter system should now be vented. If applicable, ensure that the
fi lter pump's pre-fi lter guard is slightly open until the water runs from
the pre-fi lter container (transparent cover with screw fi tting on the
upper surface of the fi lter pump).
■ Allow the fi lter container to run full of water.
■ Check the fi lter system and the connection hoses for leaks and fi x, if
necessary. Due to manufacturing tolerances, it may be necessary to
wrap tefl on tape around the connections in the case of any leakage
points before the connection hose is attached.
Filtering time
The swimming pool's water should be circulated and fi ltered at least 2
to 3 times in a 24 hour period, depending on the load and the size of the
fi lter system. The time required is based on the performance of the fi lter
system and the size of the swimming pool. However, we recommend a
minimum running time of 12 hours per day.

Electrical connection

The fi lter system you have purchased is equipped with a connection cable,
which may only be connected to a circuit with a residual current circuit
breaker (RCCB) with a rated tripping current of no more than 30mA.

Technical data:

040120 Active Balls 75
■ Filter pump: 040917
■ Circulation power 8,000 l/h
■ self-priming pump with pre-fi lter
■ maximum water temperature 35 °C
■ 230 V / 550 W
■ integrated timer
■ fi lter cover with pressure gauge
■ Tank Ø 400 mm
■ Connector Ø 32/38 mm
■ Preparation for INTEX special adapter
■ Baseplate
■ Original Steinbach Filter Balls approx. 1,150 g
■ for pools up to 40,000 l capacity
040220 Active Balls 50
■ Filter pump: 040916
■ Circulation power 6,600 l/h
■ self-priming pump with pre-fi lter
■ maximum water temperature 35 °C
■ 230 V / 450 W
■ integrated timer
■ fi lter cover with pressure gauge
■ Tank Ø 400 mm
■ Connector Ø 32/38 mm
■ Preparation for INTEX special adapter
■ Baseplate
■ Original Steinbach Filter Balls approx. 545 g
■ for pools up to 33,000 l capacity

Troubleshooting

Malfunction, Cause
fault
The pressure Dirty fi lter bed
on the pressure
gauge exceeds
1 bar
Pressure too low Pre-fi lter is dirty, pump
is not getting enough
water
Air in the pump Leak on the suction
side of the pump
Leak on the fi lter Faulty seal
Pump not running Plug is not plugged in
RCCB residual current
circuit breaker has
been tripped
Pump motor faulty
Pump motor faulty
040120_040220_v1911 EN
Rectifi cation
Clean the Filter Balls,
or they may need
replacing
Clean the pre-fi lter,
check the suction pipe
and the water level
Retighten hose clamps
and screw connections
Check seal and replace
if necessary
Check the mains plug
and the connection
cable
Switch on the RCCB
residual current circuit
breaker again. If it trips
again straight away, the
pump or the control is
faulty.
Replace entire pump
9