Operation - Scheppach HS81S Originalbetriebsanleitung

• Turn on the power tool as described and put it into

operation.

Cutting depth (Fig. 14)
Turn the round handle (11) to set the blade (3) to the
required cutting depth.
- Anticlockwise: smaller cutting depth
- Clockwise: larger cutting depth
After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions.
Setting the angle (Fig. 14-15)
With the table saw you can make diagonal cuts to the
left oriented to the stop bar from 0 ° to 45 °.
m Check before each cut, that between the stop bar
(30), cross-stop (13) and the saw blade (5) a collision
is not possible.
• Undo the fixing handle (13).
• Set the desired angle on the scale by pressing and
turning the hand wheel (12).
• Lock the fixing handle (13) again in the required an-
gle position.
Working with the rip fence
Setting the stop height (figs. 15-16)
• The stop rail (30) of the rip fence (13) has two guide
surfaces with different heights.
• Depending on the thickness of the material to be
cut, the stop rail (30) as shown in fig. 16 must be
used for thick material (about 25 mm workpiece
thickness) and that shown in fig. 15 for thin material
(less than 25 mm workpiece thickness).
Turning the stop rail (figs. 15-16)
• Loosen the wing nuts (28) first for rotating the stop
rail (30).
• Now, the stop rail (30) can be removed from the
guide rail (29) and pushed over it again using the
corresponding guide.
• Tighten the wing nuts (28) again.
• The stop rail (30) can be applied to the left or right
of the guide rail (29) as needed. To this end, only
install the bolts from the other side of the guide rail
(29).
Setting the cutting width (fig. 17)
• The rip fence (13) must be used for longitudinal cut-
ting of wood parts.
• The rip fence (13) should be mounted on the right
side of the saw blade (3).
• Place the parallel stop (13) onto the saw table in a
downwards direction.
• The parallel stop (13) can be set to the required di-
mension with the aid of the scale on the saw table.
• Clamp the parallel stop (13) securely with the lever
(31).
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Transverse stop (fig. 18)
• Push the transverse stop (7) into a groove (32) of
the saw bench.
• Loosen the handle screw (35).
• Turn the cross stop (7) until the desired angle is
set. The arrow on the transverse stop is at the set
angle.
• Tighten the knurled screw (35) again.
• The stop bar (33) can be moved on the transverse
stop (13). Loosen the nuts (34) and push the stop
rail (33) to the desired position. Tighten the nuts
(34) again.
Caution!
- Do not push the stop rail (33) too far towards the
saw blade.
- The distance between the stop rail (33) and saw
blade (3) should be about 2 cm.
Operation
Working instructions
After each new adjustment it is advisable to carry out
a trial cut in order to check the set dimensions. After
switching on the saw, wait for the blade to reach its
maximum speed of rotation before commencing with
the cut.
Secure long workpieces against falling off at the end
of the cut (e.g. with a roller stand etc.)
Take extra care when starting the cut!
Never use the equipment without the suction func-
tion.
Regularly check and clean the suction channels.
Making longitudinal cuts (fig. 19)
Longitudinal cutting (also known as slitting) is when
you use the saw to cut along the grain of the wood.
Press one edge of the workpiece against the parallel
stop (13) while the flat side lies on the saw table (1).
The blade guard (4) must always be lowered over the
workpiece.
When you make a longitudinal cut, never adopt a
working position that is in line with the cutting direc-
tion.
• Set the parallel stop (13) in accordance with the
workpiece height and the desired width.
• Switch on the saw.
• Place your hands (with fingers closed) flat on the
workpiece and push the workpiece along the paral-
lel stop (13) and into the blade (3).
• Guide at the side with your left or right hand (de-
pending on the position of the parallel stop) only
as far as the front edge of the saw blade guard (4).
• Always push the workpiece through to the end of
the splitter (6).
• The offcut piece remains on the saw table (1) until
the blade (3) is back in its position of rest.
GB 25