Using The Saw - Scheppach HS81S Originalbetriebsanleitung

4. Screw the support struts (16) to the table exten-
sions (8) with the hex bolts (20) and the hex nuts
(19)
5. Subsequently, tighten all screws.
Mounting rack (fig. 4-7)
1. Screw the four support legs (9) together with
the support struts (16) onto the saw with the hex
bolts (20) (fig. 4). For this use the saw blade key
(15a/15b), part of the delivery contents (fig. 4).
2. Now place the rubber feet (17) onto the support
legs (9) (fig. 5).
3. Now, screw the long centre brace (22) and the
short centre brace (21) onto the legs (9) using the
hexagon head bolts (20) and the hexagon head
nuts (19). Make sure that the same braces face
each other. The long centre braces (22) must
be mounted parallel to the operator's side of
the saw. (Fig. 6).
4. Using two hex bolts (20) on each, loosely secure
the and hex nuts (19) at the drill holes of the rear
support legs of the support frame (18) (fig. 7).
Attention!
Both support frames must be fastened to the
back of the machine!
5. Then, tighten all the nuts and bolts of the under-
frame.
Setting / mounting the riving knife (figs. 8-10)
m The setting Caution! Pull out the main plug!
The setting of the riving knife (6) must be checked
prior to commissioning. of the riving knife (6)
must be checked prior to commissioning.
1. Set the saw blade (3) to the max. cutting depth,
bring it to the 0° position and lock it.
2. Unfasten the bolt (23) from the bench insert (2)
using a Phillips screwdriver, and remove bench
insert (22) (fig.8).
3. The distance between the saw blade (3) and the
riving knife (6) must be max. 5 mm. (Fig. 9)
4. Loosen the mounting bolt (24) in order to pull out
the splitting wedge (6) until the right distance is
adjusted (fig. 10).
5. Tighten the mounting screw (24) again and mount
the bench insert (2).
Mounting / dismounting the saw blade guard
(figs. 11-12)
1. Place the saw blade guard (4) along with the bolt
(25) onto the riving knife (6) in a downwards direc-
tion so that the bolt sits firmly in the hole of the
riving knife (6).
2. Do not screw in the bolt (25) too tightly; the saw
blade guard (4) must move freely.
3. Plug the suction hose (5) onto the suction adapter
(26) and the connecting piece of the saw blade
guard (4). Connect a suitable splint collector onto
the suction adapter (26).
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
4. Disassembly is performed in reverse order.
Caution!
The saw blade guard (4) must be lowered onto
the workpiece before starting the sawing op-
eration.
Replacing the bench insert (fig. 8)
1. In case of wear or damage, the bench insert
(2) must be replaced; otherwise, there is an in-
creased risk of injury.
2. Unfasten the bolt (23) using a Phillips screwdriver.
3. Take out the worn bench insert (2).
4. The installation of the new bench insert is done in
reverse order.
Installing / replacing the saw blade (fig. 13)
1. Caution! Pull out the main plug and wear safe-
ty gloves.
2. Dismount the saw blade guard (4)
3. Remove the bench insert (2)
4. Loosen the nut by placing a saw blade spanner
(15b) on the nut while holding up another saw
blade spanner (15a) on the motor shaft.
5. Caution! Turn the nut in the direction of rotation
of the saw blade.
6. Remove the outer flange and remove the old
blade inner flange.
7. Clean the saw blade flange thoroughly with a wire
brush before mounting the new saw blade.
8. Insert the new saw blade in reverse order and
tighten.
Caution! Note the direction of run, the cutting
slope of the teeth must be in the direction of
run, i.e. facing forward.
9. Remount and adjust the bench insert (2) and saw
blade guard (4)
10. Before you start working again with the saw,
check proper functioning of the safety equipment.

Using the saw

On/Off switch (Fig. 14)
• The saw can be switched on by pressing the green
pushbutton „I". (10)
• The red pushbutton „0" (10) has to be pressed to
switch off the saw.
Overload protection (Fig. 14)
This electrical power tool is provided with an
overload protection. In case that the overload
protection was initiated, proceed as follows:
• Disconnect the power tool from the power supply.
• Allow the power tool to cool down.
• Check the power tool carefully for possible dam-
ages.
• Have damages repaired before re-starting the pow-
er tool.
• Connect the power tool to the power supply.
• Push the overload switch (27).