Siemens SINUMERIK 840DE sl Bedienhandbuch Seite 14

Inhaltsverzeichnis
8.1.1 Allgemeines............................................................................................................................... 281
8.1.2 Zentrieren (CYCLE81) .............................................................................................................. 282
8.1.3 Bohren (CYCLE82) ................................................................................................................... 285
8.1.4 Reiben (CYCLE85) ................................................................................................................... 287
8.1.5 Ausdrehen (CYCLE86) ............................................................................................................. 289
8.1.6 Tieflochbohren (CYCLE83) ....................................................................................................... 293
8.1.7 Gewindebohren (CYCLE84, 840) ............................................................................................. 297
8.1.8 Bohrgewindefräsen (CYCLE78)................................................................................................ 303
8.1.9 Positionen und Positionsmuster................................................................................................ 307
8.1.9.1 An-/Abfahren ............................................................................................................................. 307
8.1.10 Beliebige Positionen (CYCLE802) ............................................................................................ 308
8.1.10.1 Funktion..................................................................................................................................... 308
8.1.11 Positionsmuster Linie (HOLES1), Gitter oder Rahmen (CYCLE801)....................................... 311
8.1.12 Positionsmuster Kreis (HOLES2).............................................................................................. 314
8.1.13 Positionen ein- und ausblenden................................................................................................ 317
8.1.14 Positionen wiederholen ............................................................................................................. 319
8.1.14.1 Funktion..................................................................................................................................... 319
8.2 Drehen....................................................................................................................................... 320
8.2.1 Allgemeines............................................................................................................................... 320
8.2.2 Abspanen (CYCLE951)............................................................................................................. 320
8.2.3 Einstich (CYCLE930) ................................................................................................................ 323
8.2.4 Freistich Form E und F (CYCLE940) ........................................................................................ 326
8.2.5 Gewindefreistiche (CYCLE940) ................................................................................................ 328
8.2.6 Gewindedrehen (CYCLE99) ..................................................................................................... 331
8.2.7 Gewindekette (CYCLE98)......................................................................................................... 340
8.2.7.1 Parameter.................................................................................................................................. 342
8.2.8 Abstich (CYCLE92) ................................................................................................................... 344
8.3 Konturdrehen ............................................................................................................................ 346
8.3.1 Allgemeines............................................................................................................................... 346
8.3.2 Darstellung der Kontur .............................................................................................................. 347
8.3.3 Neue Kontur anlegen ................................................................................................................ 349
8.3.4 Konturelemente erstellen .......................................................................................................... 351
8.3.5 Passungsmaß eingeben ........................................................................................................... 356
8.3.6 Kontur ändern ........................................................................................................................... 358
8.3.7 Konturaufruf (CYCLE62) - nur bei G-Code-Programm............................................................. 359
8.3.8 Abspanen (CYCLE952)............................................................................................................. 360
8.3.9 Abspanen Rest (CYCLE952) .................................................................................................... 366
8.3.10 Stechen (CYCLE952)................................................................................................................ 369
8.3.11 Stechen Rest (CYCLE952) ....................................................................................................... 372
8.3.12 Stechdrehen (CYCLE952) ........................................................................................................ 374
8.3.13 Stechdrehen Rest (CYCLE952)................................................................................................ 378
8.4 Fräsen ....................................................................................................................................... 381
8.4.1 Planfräsen (CYCLE61).............................................................................................................. 381
8.4.2 Rechtecktasche (POCKET3) .................................................................................................... 385
8.4.3 Kreistasche (POCKET4) ........................................................................................................... 391
8.4.4 Rechteckzapfen (CYCLE76) ..................................................................................................... 397
8.4.5 Kreiszapfen (CYCLE77)............................................................................................................ 401
8.4.6 Mehrkant (CYCLE79)................................................................................................................ 405
8.4.7 Längsnut (SLOT1)..................................................................................................................... 408
8.4.8 Kreisnut (SLOT2) ...................................................................................................................... 414
8.4.9 Offene Nut (CYCLE899) ........................................................................................................... 419
14
Bedienhandbuch, 03/2013, 6FC5398-8CP40-3AA1
Drehen