Blue Tooth Hand Free Operation - Clatronic AR 759 Bedienungsanleitung

12. BLUE TOOTH HAND FREE OPERATION

USER GUIDE FOR BLUE TOOTH OPERATION
1. When user use our Blue tooth HEAD UNIT, please make sure the mobile phone you use must / does support
Blue tooth functions (Headset or Handsfree profiles or both)
2. Before you start to use our Bluetooth HEAD UNIT, please make sure complete pairing with your mobile phone
first. Please refer to the user manual, section "PAIRING" for detail "PAIRING" instruction.To ensure the best re-
ception for Pairing or Re-connection, please make sure the Phone Battery is fully charged when making the Pair-
ing or Re-connection.
3. Please always try pairing the Mobile Phone with Head unit after a few minutes of the Mobile Phone was
Switched On to ensure the best pairing result.
4. "BT60" is this unit device model number which is displayed on the mobile phone.
5. To achieve the best performance, please always keep the Mobile Phone within 3 meters of the Head unit.
6. Please always keep a clear path between the Mobile Phone & the Head unit.
7. Never put any metal object or any obstacle between the path of the Mobile Phone & the Head unit.
8. Some brand of Mobile Phone like Sony Ericsson may have "Power Saving Mode" selection when Blue Tooth
mode is switched on. PLEASE DO NOT Switches ON Power saving Mode when operating with this Head Unit,
as some abnormal communal behavior will happen occasionally if Power Saving Mode is switched on.
9. Before user make Outgoing call or Incoming call, make sure the mobile phone's "Blue Tooth function" was
switched "ON".
10. To ensure the best conversation quality / performance, please always keep talking within 1 meter of the Head
Unit.
11. If user want to Dis-connect the Head unit with the Mobile Phone, please switch "OFF" Blue Tooth connectivity on
the Mobile Phone, or go to the system menu, "dis-connect" to disconnect the bluetooth connectivity manually.
(please refer to the user manual, section "dis-connection of the bluetooth system for details instruction).
12. Some Mobile Phones can support "IN BAND RING TONE", such as Nokia. In such case, the Incoming Ringing
Tone will be same as the original Ring-tone of the Mobile Phone. But some Mobile Phones like Sony Ericsson do
not support this feature. The Ring-tone will be using the standard Ring-tone of the Head unit.
13. When in telephone mode, during talking, it is highly recommended to set the volume to below "30" in
order to achieve the best sound quality. As if the volume is too high, it may create unwanted echo inside
the car, and this unwanted echo may feedback into the microphone.
14. If the Bluetooth related operation is not performing normally, like cannot make pairing, cannot making an outgo-
ing call, User can try to make a SOFT-RESET of the Bluetooth module by removing / detaching the panel from
the main unit and waiting for about 1 min. Then re-attach the panel to the unit & retry the Bluetooth operation
again. Or user can RESET the whole unit by pressing the RESET button behind the panel.
By pressing the RESET button all the stored memory will resume to factory default.
With Bluetooth radios it is absolutely neseccary to mind a correct connection over the ignition. Other-
wise there is no correct seperation of radio link between radio and mobile phone.
FAQ (FREQUENCY ASKING QUESTIONS)
Q: Under phone conversation, if the voice output from the car's speakers is not loud enough.
A: Try increase the volume level of the head unit to a suitable sound level.
Q: Under phone conversation, the „Listener" cannot hearing my voice loud enough.
A: First, try asking the „Listener" increase the volume level of his/her mobile phone, if still not loud enough,
try to increase your mobile phone's volume.
Q: Under phone conversation the „Listener" can hear echo feedback.
A: Your unit's speaker volume level is too loud which cause the voice feedback into the built-in microphone,
this can be corrected by decreasing the volume level.
Q: Under phone conversation, the „Listener" complain the background is too noisy.
A: Maybe you are in a noisy enviroment. Try close the car's window to shield the enviroment / background
noise under phone conversation.
Q: If the mobile phone already paired with the headunit, but after several calls the incoming calls cannot ac-
cess thru the headunit.
A: Maybe the paired mobile phone lost the Bluetooth connection with the headunit. In this case, please go to
the "MENU" & select "Re-Con" to reconnect the headunit with the paired mobile phone. For details,
please refer to the MENU operation "re-connection".
55