Lnb Set-Up; Channel Set-Up - Strong srt 4356 pvr Bedienungsanleitung

Part 1 • English
5.1.4.2 LNB Set-up (Please see inside cover Screen 17)
It is recommended that you read the manual and installation instructions of your LNB,
your DiSEqC switch, your 0/12V switch and your Positioner before you start setting up
your LNB.To set up your LNB, please apply the following steps:
1. Press the Menu button.
2. Using UP/DOWN keys, select
"Installation" and press OK.
3. Using UP/DOWN keys, select "LNB Set-up" and press OK.
4. Check the exact specifications of your LNB through the manufacturers information
or your dealer. There are up to 16 types of LNB's available.The Default is set to
Universal mode (9750/10600MHz), DiSEqC is not used and the LNB is mounted
on a fixed dish.
5. Use the UP/DOWN keys on your remote to select an item and use the
LEFT/RIGHT buttons to set up any values.
LNB: Up to 16 LNBs are available, select the correct one according to your
LNB specifications.
LNB Type: Select the LNB type from Universal 1 - 3, and Single. You should
type the LNB value in Single. In Single, the item parameter is 0 or another
number. In UNI 1-9750/10600
9750/10750 MHz
LNB Power: Select 13/18V, 13V or 18V for LNB. Select "Oil" if you want to
switch the power of the LNB off.
LNB Dish: Using the Left/Right buttons, select "Fixed" or "Motorized" (Move)
Dish. If you use a motorized dish, read the "Positioner Set-up" (Described in
section 5.1.4.3.1 ).
DiSEqC switch: The default is Off. To use the DiSEqC switch, set up the
DiSEqC version you have (V 1.0 or V 1.1 ).
DiSEqC Input: Select position 1-4 if DiSEqC switch is DiSEqC V1.0.Select
position 1-16 if DiSEqC switch is DiSEqC V1.1.
DiSEqC Repeat: Designate the repeat of switching. (0 - 3)
Switch 0/12V: You can set the 0/12V switch On or Off. This is for the black
RCA Output at the back of your receiver.
Switch 22KHz: You can set the 0/22kHz switch to ON or OFF.
www.strongsat.com
MHz, UNI2-9750/10700MHz, UNI3
23
Tip: If you set "LNB type" to "Universal" (UNII - UNI3), you will not be able to change
settings in both the "LNB Power" menu item and the "Switch 22kHz' menu item. If you
want to change any of these two settings you must set "LNB type" to zero. If DiSEqC
switch is Off, you will not be able to change settings in both the "DiSEqC Input" and
"DiSEqC Repeat" menu items. Alternatively if you set LNB Dish to "Moved", the
DiSEqC switch menu item is automatically switched to off if your "LNB dish" is set to
"fixed" you will be able to select the required DiSEqC level in the DiSEqC switch menu
item.
6. Press the Red (Save) button, the Blue (Save &Exit) button to save the setting.
7. Press the Green (Exit) button or Exit button if you don't want to save the setting.
5.1.4.3 Channel Set-up (Please see inside cover Screen 18)
The channel set-up is for downloading tile channels available on the satellites.
There are up to 64 satellites available. To download channels, please apply the
following steps:
In this menu, you can edit the satellites name, and edit the transponder of the satellite.
You can also display the LNB menu and the Positioner Set-up menu by selecting LNB
and Dish Position respectively.
1. Press the Menu button.
2. Using UP/DOWN keys on your remote, select "Installation" and press OK.
3. Using UP/DOWN keys, select "Channel Set-up" and press OK.
4. Use the UP/DOWN keys on your remote to select an item and use the Left/Right
button to set up any values.
Satellite: Select "Satellite" and press OK or the Right button. The satellite list
is displayed and then you can choose a satellite from which you want to
download your channels from by pressing OK.
Tip: If you want to rename the satellite, press the FUNC button on the remote
control when you are in the list of satellites.
LNB: Select "LNB" and press OK or the Right button. In the "LNB field", select
one of the available LNB's. If you want to set LNB related values, press OK
and the LNB Set-up menu (Described in section 5.1.4.2) will be displayed.
24
Part 1 • English
www.strongsat.com