The Installation Menu; System Set-Up Menu - Strong srt 4356 pvr Bedienungsanleitung

Part 1 • English
Channel: You can select the channel to be recorded when the Timer mode is
PVR record, Time Interval or power on, or the channel displayed when the
power is ON.
3. Press the Red button to save and proceed with another timer event
4. Press the Blue button to save and exit the timer menu
5. Press the Green button to exit the timer menu WITHOUT saving the settings
Tip: You have to select the channel, starting time, and ending time settings if the Timer
mode is "Time interval" or "PVR Recording". An error message will appear if any of the
settings are incorrect. Especially in PVR Record, be sure to check the hard disk
capacity, starting time and ending time.
5.1.4 The Installation Menu. (Please see inside cover Screen 9)
All settings that are related to TV, Dish, LNB and Satellites are within this menu. The
installation menu contains several sub menus such as "System Set-up ", "LNB Set-up
", "Channel Set-up" and "Parental Lock". To access the different sub menus, apply the
following:
5.1.4.1 System Set-up Menu (Please see inside cover Screen 10)
To install your receiver to your personal preferences, go to "System Set-up" menu.
Then please apply the following steps:
1. Press the Menu button.
2. Using UP/DOWN keys, select "Installation" and press OK.
3. Using UP/DOWN keys, select "System Set-up" and press OK.
Language Settings: You can change the language of the menu, audio and
subtitles by applying the following steps:
1. Select "Language Settings" and Press OK or the Right button.
2. Select "Menu Language' and Press OK or the Right button.
3. Using UP/DOWN keys, select the language in which you want your menu to be
displayed and press OK. The screen of the menu will change to the language of
your choice.
4. You can also choose your preferred first audio language, second audio
language and the subtitle language by applying the same steps.
www.strongsat.com
5. Press EXIT until you return to the main menu.
TV/VCR Settings: You can set the TV/VCR settings to your personal
preferences. Check your TV and VCR user manuals for the correct settings.
You can change your TV/VCR settings by applying the following steps: (Please
see inside cover Screen 11)
1. Select "TV/VCR Settings" and press OK or the Right button.
TV Mode: Press OK or the Right button and set your TV mode to "Multi",
"PA L " or "NTSC ".
Video Mode: Press OK or the Right button and set your VCR mode to
"CVBS" (Composite video) or "RGB" (preferred option if your TV set is
compatible with it).
Screen Mode: Press OK or the Right button and set your screen mode to
"Full Screen" or "Letterbox".
Audio Mode: Press OK or the Right button and set your audio output to
"Stereo ", "Left only" or "Right only" (left or Right is for mono TV sets)
SPDIF Output: Press OK or the Right button and activate your S/PDIF
output on the back of your receiver, so you can connect it to a digital Audio
amplifier using an optic fiber cable.
VCR Scart: Press OK or the Right button and set the scart output to "Auto"
or "STB" (Set Top Box). If set to "STB ', the VCR scart signal is not
automatically looped through.
UHF Mode: Press OK or the Right button and set the UHF mode to "PAL
B/G", "PAL l" or "PAL D/K". If the TV set is connected using a coaxial (RF)
cable, you must select RF modulator type here. The RF modulator type
affects the channel audio.
UHF Channel: Press OK or the Right button and set the UHF channel
number to the same UHF channel number of your TV set. This only has to
be done if your TV set is connected with a coaxial (RF) Cable. If the UHF
Channel numbers of the receiver and the TV set are not set the same, no
picture will be displayed.
2. Press EXIT until you go back to main menu.
OSD Settings: You can set the OSD (On Screen Display) on your TV to your
19 20
Part 1 • English
www.strongsat.com