Sony UP-897MD Gebrauchsanweisung Seite 47

Item Function
LOAD To load the
registered settings
MEDIA To select the type
of paper
MEMRY To select the
memory mode
MENU To print the menu
settings currently
selected
MULTI To specify the
number of images
to be printed on
one sheet of the
printout
PAGE Each time you
(This item is press the PRINT
not displayed button, the image
when is stored in
"MU:MLT" memory. Up to
is selected in ten images can be
"MULTI." stored.
You can select the
desired image
from 10 kinds of
images stored in
memory and
make a printout.
Settings
LO:3: Loads the "SA:3"
settings registered using the
"SAVE" menu item.
LO:2: Loads the "SA:2"
settings registered using the
"SAVE" menu item.
[LO:1]: Loads the "SA:1"
settings registered using the
"SAVE" menu item
BACK: Cancels the setting
change and returns to the
item selection column.
ME:S: Uses the UPP-110S.
ME:HD: Uses the UPP-
110HD.
[ME: HG]: Uses the UPP-
110HG
BACK: Cancels the setting
change and returns to the
item selection column.
ME:FLD: When printing
fast-moving images (such
as a ball being thrown), the
printout may be blue. If this
happens, select this setting.
[ME:FRM]: Normally
select this setting.
BACK: Cancels the setting
change and returns to the
item selection column.
[ME:OK]: Prints the menu
list currently set.
BACK: Cancels printing
and goes back to its item
column.
MU:MLT: Prints two
images on one sheet of the
printout (two reduced
images).
[MU:SGL]: Prints one
image. (full-size image).
BACK: Cancels the setting
change and returns to the
item selection column.
[PG:1] to PG:10: Prints by
selecting the desired ONE
image from among images
1 to10 and pressing the
COPY button.
BACK: Cancels the setting
change and returns to the
item selection column.
Item Function
QTY To set the print
quantity
SAVE To register up to
three kinds of
settings
SCALE To enlarge or
reduce the image
to be printed
c)
SCAN To set the range
of the image to be
printed
SFT.H To specify the
horizontal
position of the
image to be
printed
SFT.V To specify the
vertical position
of the image to be
printed
Adjustments and Settings Using the Menu
Settings
[QT:1] to QT:9: Makes the
same printouts. You can
select the desired number of
same printongs between 1
and 9.
BACK: Cancels the setting
change and returns to the
item selection column.
SA:3: Registers the menu
settings as No.3.
SA:2: Registers the menu
settings as No.2.
[SA:1]: Registers the menu
settings as No.1.
BACK: Cancels the setting
change and returns to the
item selection column.
The scale can be set
between SCL:2.0 (two
times) and SCL:0.5 (one
half) in increments of 0.5.
[SCL:1.0] is the factory
setting.
BACK: Cancels the setting
change and returns to the
item selection column.
The range is widened in the
sequence of SC:NOR,
[SC:WD1] and SC:WD2.
BACK: Cancels the setting
change and returns to the
item selection column.
[S.H:0]: Adjusts the
horizontal position. The
numeric value displayed by
turning the jog dial depends
on the settings of
"SCALE", "SCAN", and
"SIDE", and the signal
system of the image to be
captured.
BACK: Cancels the setting
change and returns to the
item selection column.
[S.V:0]: Adjusts the vertical
position. The numeric value
displayed by turning the jog
dial depends on the settings
of "SCALE", "SCAN", and
"SIDE", and the signal
system of the image to be
captured.
BACK: Cancels the setting
change and returns to the
item selection column.
47