Siemens SINUMERIK 810D Handbuch Seite 169

09/2011
SpacerSize=0
;---SkipFirstSpacerMark---: 0= NO 1 = YES (to suppress Spacer before 1. NC Programm)
SkipFirstSpacerMark=0
;---SpacerMarkers (max 16 Byte each)
;---SpacerMark1..3 ---: (before each line in which these SpaceMarkers appear a
spacer will be inserted)
;SpacerMark3=%MPF
SpacerMark1=
SpacerMark2=
SpacerMark3=
;---SpacerMarkInsertAfter1..3 ---:(after each line in which this SpacerMarkers
appear a spacer will be inserted)
;SpacerMarkInsertAfter3=M30
SpacerMarkInsertAfter1=
SpacerMarkInsertAfter2=
SpacerMarkInsertAfter3=
;---EOBcode---:
CNC)
; 0=No, 1 = CR + CR, 2 = CR + LF, 3 = LF + CR, 4 = LF + LF,
; 5 = CR + CR + CR,
; 9 = LF + CR + CR,
; 13 = CR, 14 = LF
EOBcode=0
;---SuppressComment---: 0= NO 1 = YES (comments will not be transferred)
SuppressComment=0
;---SendTimeOut in minutes---: 0= infinite (job will be cancelled after that time,
if machine is not in receive mode)
SendTimeout=1
;---Different Baudrate for sending---: (SendBaudRate=0 = same Baudrate as in [COM]
section)
SendBaudRate=0
;---SendDelay in seconds---: (the system waits for this time before the data will be
send to the machine)
SendDelay=0
;Program Input Parameter
[RECEIVE]
;---Parameters in ASCII- Dezimal- Code (0 ... 255)---
;---ValidData---: (This charakter shows the first valid character of the NC-program.
All charakters before will be cut)
ValidData=0
;---ProgramStart---: (character in ASCII dec. added in front of each file after
uploading)
ProgramStart=0
;---ProgramEnd---: (character in ASCII dec. trailed at the end of each file after
uploading)
ProgramEnd=0
;---EofChar---: (character, which indicates the end of uploading) 0=none -> receive
ends after TimeOut (see below)
EofChar=0
;TimeOut in seconds. Uploading is stopped after this time, if no bit further more is
received (1 ... 600, 0=infinite)
TimeOut=5
;---HeaderSize---: (Size in Bytes to cut from program header after receiving each
file)
HeaderSize=0
;---TrailerSize---: (Size in Bytes to cut from program end after receiving each
file)
TrailerSize=0
;---NullDiscard---: 0 = NO 1 = YES (binary NULL values will discarded everywhere in
the file)
NullDiscard=1
;---TestMode---: 0 = NO 1 = YES (received Tmpfile will not be deleted)
TestMode=0
;---NCSplit---: 0= deactivated
NCSplit=0
;---NCNameLines---: (number of the signifcant lines, beginning with line 1)
NCNameLines=5
;---NCNameBegin---: Startmark in front of NameInfo
NCNameBegin=#Name#
;---NCNameEnd---: Endmark behind NameInfo
NCNameEnd=#End#
;---NCNameWPD---: seperator between WPD and Name
NCNameWPD=
;---NCNameType---: seperator between Name and Type
NCNameType=
;
NCProgrammStart1=%
© Siemens AG 2011 All Rights Reserved
Motion Control Information System DNC (FBDN) - 09/2011
(This parameter is used for the end of line conversion to/from
6 = CR + CR + LF,
10 = LF + CR + LF,
1 = SINUMERIK 840D
DNC Plant/DNC Cell (FBDN1)
7 = CR + LF + CR,
11 = LF + LF + CR, 12 = LF + LF + LF,
2 = any other CNC
10 Konfiguration
8 = CR + LF + LF,
FBDN1/10-165