Inhaltsverzeichnis - Mettler Toledo InPro 6000 Bedienungsanleitung

4
Contents
1 Introduction .................................................................... 5
2 Important notes .............................................................. 6
2.1 Notes on operating instructions .......................................... 6
2.2 Intended use .................................................................... 6
2.3 Safety instructions ............................................................ 7
2.4 Examples of some typical applications ............................... 8
2.5 Use in Ex-zones .............................................................. 8
2.6 Ex-classification ATEX ...................................................... 8
2.6.1 Introduction ..................................................................... 8
2.6.2 Rated data ...................................................................... 9
2.6.3 Special conditions ............................................................ 9
3 Product description ....................................................... 11
3.1 General information ........................................................ 11
3.2 Principle ....................................................................... 11
3.3 Scope of delivery ............................................................ 12
3.4 Equipment features ......................................................... 12
4 Installation ................................................................... 15
4.1 Mounting the sensor ....................................................... 15
4.1.1 Retrofit kit for InPro 6870 i / InPro 6960 i / InPro 6970 i ....... 15
4.2 Connection .................................................................... 16
4.2.1 Connecting the optical sensor to a cable ........................... 16
4.2.2 Digital connection to a transmitter .................................... 16
4.2.3 Analog connection to transmitter or controller .................... 17
4.2.5 MODBUS Installation ...................................................... 18
4.2.6 Power Connection of sensor ............................................ 18
5 Operation ..................................................................... 19
5.1 Start-up ......................................................................... 19
5.2 Configuration ................................................................. 19
5.2.1 Sensor detection ............................................................ 19
5.2.2 Sampling rate ................................................................ 19
5.2.3 LED mode ..................................................................... 19
5.3 Calibration .................................................................... 20
5.3.1 Purpose of calibration ..................................................... 20
5.3.2 Factory calibration .......................................................... 22
5.3.3 Single point calibration (Slope or Process Calibration) ....... 22
5.3.4 Slope calibration (InPro 6870 i and InPro 6960 i) ............. 22
5.3.5 Process calibration ........................................................ 23
5.3.6 Dual point calibration ..................................................... 23
5.3.7 Calibration when connected with analog signal ................ 24
5.3.8 Reset to factory calibration ............................................. 24
6 Maintenance ................................................................. 25
6.1 Sensor inspection ........................................................... 25
6.1.1 Visual inspection ............................................................ 25
6.1.2 Testing the sensor with the transmitter .............................. 25
6.1.3 ISM ............................................................................. 26
6.2 Replacing the OptoCap ................................................... 27
7 Storage ........................................................................ 28
8 Product specification ..................................................... 29
8.1 Certificates .................................................................... 29
8.2 Specifications ................................................................ 29
9 Ordering information ..................................................... 31
9.1 Sensors ........................................................................ 31
9.2 Accessories ................................................................... 31
9.3 Spare parts .................................................................... 32
9.4 Recommended transmitters ............................................. 32
9.5 Recommended housings ................................................ 33
10 Theory of the optical oxygen measurement ..................... 34
10.1 Introduction ................................................................... 34
10.2 Principle ....................................................................... 34
10.3 Principle of the design of the optical oxygen sensor ........... 34
10.4 Temperature .................................................................. 35
10.5 Dependence on flow ....................................................... 35
10.6 Oxygen partial pressure - oxygen concentration ................ 35
InPro 6000 optical O
52 206 256
InPro 6000 Series Optical O
sensors © 01/ 2016 Mettler-Toledo GmbH
2
Sensors 12 mm
2
Printed in Switzerland