Amp Device Mode - Arcam AVR400 Handbuch

aMP device Mode

AMP
The A Device Mode button configures the Cr102 to
control the AVr400. Pressing this button does not affect
the currently selected input on the AVr400.
IMPORTANT: The Cr102 must also be in Device
AMP
Mode to control the following sources: (multi-
MCH
channel analogue), , (optional network audio),
AUX NET
, (for use with the optional Arcam drDock or
USB iPOD
irDock).
However to control the internal Tuner (AM/FM/DAB
(if fitted)) the Cr102 must first be in Device Mode
TUN
(see later).
The functionality of the Cr102 is context sensitive for
the internal sources and is described in the following
table.
Single press – Toggles AVr400 power
P
between standby and on in the current zone
(zone in which the command is received).
Press and hold – Forces all AVr400 zones
into standby, regardless of which zone the
command was received in.
9 The number keys can be used for source
0
...
selection (without changing the Cr102
Device Mode). Alternatively the Device
Mode buttons can also be used with the
key.
SHiFT
0
(satellite) input
SAT
2
input
AV
3
input
TUNER
4
input
BD
5
input
DiSPlAy
6
input
VCR
7
input
CD
8
(front panel) input
AUX
9
(multichannel) input
MCH
Selects the Display input on the AVr400
PHONO
E (television Audio return Channel).
(for and sources)
iPOD NET
RPT
r
Modifies many keys (see individual key
S
descriptions below).
Selects (multichannel) input on the
MCH
AUX
H AVr400
+ H selects
input on the AVr400
SHiFT AUX
Selects input on the AVr400
iPOD
NET
e
+ e selects network ( ) internal
SHiFT NET
input on the AVr400
navigate menus
confirms a setting (equivalent to 'Enter'
Ok
or 'Select' on some remote controls)
+ > increases the picture resolution.
SHiFT
+ ' turns current zone (in which
SHiFT
command is received) on
+ , turns current zone (in which
SHiFT
command is received) off.
Cycles through the available surround and
M
downmix modes.
Displays the AVr400 setup menu on the On
U
Screen Display (see page E-34).
Cycles through the front panel display's
D
brightness options
Toggles the mute function of the AVr400
@
] [ (track control for and sources)
iPOD NET
+ [ Follow Zone1 source.
SHiFT
When the command is received in Zone2
the source for that zone follows whatever
input source is selected in Zone1
- + Decrease ( ) and increase ( ) AVr400
– +
volume
Stereo direct on/off. Provides a direct
DIRECT
) analogue path from the analogue inputs to
the left and right front outputs. Switches off
any surround processing modes and shuts
down the DSP circuits for the best stereo
sound quality.
Displays the room EQ settings menu
EQ
$
(for and sources)
iPOD NET
EFFECT
&
Calls up a pop-up (and front screen) to
BASS
( adjust the bass setting for a particular input.
Brings up the speaker trim menu.
TRIm
!
Use the , , and navigation
B C D E
buttons. Press again to exit the speaker
TRiM
trim menu.
As this is a temporary adjustment, these
additional trim levels are reset back to the
values set in the Speaker Levels menu when
the unit is turned off or the unit is put
into standby. These temporary trim levels
override the speaker levels found in the
setup menu.
Delays may be introduced into the video
SyNC
# signal by video processing which causes
a mismatch between the audio and video
timing. You will notice this by speech sound
being out of synchronization with the lip
movements in the video.
To compensate for this, you can adjust the
lip sync delay. Press the button and
SyNC
use the and navigation buttons. Press
D E
again to exit the lip sync trim menu.
e-26
Brings up a temporary subwoofer trim
SUB
% control. Use the and navigation
D E
buttons. Press again to exit the sub trim
SUB
menu.
As this is a temporary adjustment, the sub
trim level is reset back to the value set in
the Speaker Levels menu when the unit is
turned off or the unit is put into standby.
Calls up a pop-up (and front screen) to
TREBLE
h adjust the treble setting for a particular
input.
(for and sources)
iPOD NET
FAV+
u
(for and sources)
iPOD NET
FAV-
t
(for source)
NET
HOmE
o
Cycles through the information displayed
INFO
b on the lower left portion of the front panel
display.
iPod commands
The iPod interface is selected by pressing e in
AMP
Device Mode on the Cr102. When connected to an
iPod via an optional drDock/irDock, the keys below are
used to navigate music files in Device Mode.
AMP
navigate the files on screen.
selects/play the highlighted file.
Ok
Toggles random (shuffle) play of the playlist
RPT
on and off.
r
+ r cycles through the repeat options
SHiFT
Selects the previous/next track in the
] [
current playlist
Begins or resumes playback at the currently
$
highlighted track
Toggles pause and playback of the current
&
track
# Stops playback