Battery Charging; Installing The Transmitter Batteries (Rtf Only); Installing The Flight Battery; Transmitter And Receiver Binding - Blade MCX2 Bedienungsanleitung

6

Battery Charging

Follow these steps to charge the Li-Po battery with the included charger:
• Remove the cover on the bottom of the charger and install four of the included AA batteries, noting
proper polarity. Replace the cover after the AA batteries are installed.
• Slide the battery into the slot on the charger. The endcap of the battery has been specifically designed
to allow the battery to be slid into the slot easily one way (usually with the label on the battery facing
outward) to prevent reverse polarity connection. However, check for proper alignment and polarity
before proceeding to the next step.
• Gently press the battery and its connector into the charge jack/connector located at the bottom of the
slot on the charger.
• Once the connection is successful, the LED light on the charger turns solid red, indicating charging has
begun.
• A fully discharged battery (not over-discharged) takes
approximately 30–40 minutes to charge. As the battery nears full charge, the LED light will blink. When
the battery is fully charged the LED light blinks approximately every 20 seconds or goes out entirely.
Note: The Li-Po battery included with your Blade mCX2 will arrive partially charged. For this reason the initial
charge may only take 15–20 minutes.
Note: You can expect to charge the Li-Po flight battery approximately 15–20 times before it will be necessary
to replace the AA batteries in the charger.
An optional 6V power supply is also available separately (EFLC1005). This power supply will allow you
to charge at home without the need for AA batteries.

Installing the Transmitter Batteries (RTF ONLY)

Install four of the included AA batteries in the transmitter. Check for proper operation of the transmitter by
switching the power switch on (to the left). The LED light at the top of the transmitter should begin to glow
solid red while the transmitter beeps.

Installing the Flight Battery

Once the Li-Po battery is fully charged, you can install it in the helicopter. This is done by sliding it into the
battery mounting supports/slots just below the main gears. Slide the battery into the slots with the label
facing downward and the connector oriented toward the back of the helicopter.
Note: Be sure to slide the battery into the slots until the endcap of the battery comes into contact with the
rear battery support. This allows you to achieve the correct center of gravity for the best overall flight
performance. However, be sure the battery is not pushed far enough forward that it makes contact with
the servo gears, as this could cause damage to the gears and a potential crash.

Transmitter and Receiver Binding

The Blade mCX2 RTF comes bound to the MLP4DSM transmitter included.
The BNF version requires you to bind to your own compatible DSM2 Aircraft Transmitter.
To bind or re-bind your mCX2 to your chosen transmitter please follow the directions below:
Binding is the process of programming the receiver of the control unit to recognize the GUID (Globally
Unique Identifier) code of a single specific transmitter. You need to 'bind' your chosen Spektrum DSM2
technology equipped aircraft transmitter to the receiver for proper operation.
Following are some of the Spektrum DSM2-equipped transmitters and modules that bind to the receiver of
your Blade mCX2.
E-flite MLP4DSM E-flite LP5DSM
PKZ Ember 2 Transmitter JR 12X 2.4
Spektrum DX5e Spektrum DX6i
Note: The Spektrum DX6 (SPM2460) is equipped with DSM (not DSM2) technology and is not compatible with
the receiver of the Blade mCX2.
The following steps outline the binding process:
• Make sure the flight battery is disconnected from the 5-in-1 unit and the transmitter is turned off.
• Plug the flight battery into the 5-in-1 unit.
• Plug the flight battery into the 5-in-1 unit. After 5 seconds the LED on the 5-in1 unit will begin flashing.
MLP4DSM and ParkZone Vapor/Ember 2 Transmitters
After verifying the LED is flashing on the receiver/5-in-1, PUSH directly down on the left-hand stick while
switching the transmitter on (you will feel a 'click' when you push in on the end of the stick).
7
ParkZone Vapor Transmitter
JR X9303 2.4
Spektrum DX7/DX7se