Storage And Transport - Scheppach Hbs261 Originalbetriebsanleitung

• Clean the product at regular intervals using a damp
cloth* and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the product. Make sure that no water can pen-
etrate the product interior.
12.2 Maintenance
Tool required:
• Allen key, 5 mm* (B)
• Allen key, 6 mm* (C)
• Circlip pliers*
• Phillips screwdriver*
* = may not be included in the scope of delivery!
12.2.1 Replacing the band saw blade (6)
(Fig. 1, 3, 11, 13, 16)
1. Set the band saw blade guard (5) to about half height.
2. Open the housing doors (11) by loosening the Allen
screws (11b).
Use a 5 mm Allen key (D).
3. Pull out the saw table (8) as described under 10.1 and
remove the hexagon screw (K) and the wing nut (L).
4. To relieve the band saw blade (6), turn the clamping
screw (2) anti-clockwise.
5. Remove the band saw blade (6) of two band wheels
(23, 25) and remove the band saw blade (6) from the
slot in the saw table (8).
6. Thread the new band saw blade (6) through the slot in
the saw table (8) and place it in the centre of the run-
ning surface (24) of both band wheels (23, 25). The
teeth of the band saw blade (6) must point downwards
in the direction of the saw table (8).
7. Tension and adjust the band saw blade (6) (see 9.3,
9.2).
8. Once the adjustment is complete, close the housing
doors (11) again and secure the Allen screws (11b).
Use a 5 mm Allen key (D).
12.2.2 Replacing the table inlay (32) (Fig. 23)
Notes:
• Wear protective gloves.
• In the event of wear or damage the table inlay (32)
must be replaced; otherwise there is an increased risk
of injury.
1. Move the saw table (8) to the 0° position as described
under 8.2.
2. Remove the Phillips screw (32a) from the worn table
inlay (32) and push the table insert out of the saw ta-
ble (8) from bottom to top.
Use a Phillips screwdriver*.
3. Installation of the new table inlay (32) takes place in
reverse order.
* = may not be included in the scope of delivery!
12.2.3 Tensioning the belt (29)
(Fig. 11, 17, 18)
1. Open the lower housing door (11) by loosening the Al-
len screws (11b). Use a 5 mm Allen key (D).
2. Loosen the belt tensioning screw (29a) on the motor
(16).
Use a 6 mm Allen key (E).
3. Push the motor (16) slightly backwards and retighten
the belt tensioning screw (29a) on the motor (16) to
tension the belt (29).
Use a 6 mm Allen screw (E).
Ensure that the notches interlock and that the belt (29)
is centred on the drive belt pulley (30) and the band
wheel pulley (31).
4. Close the lower housing door (11) again and secure it
with the Allen screw (11b). Use a 5 mm Allen key (D).
12.2.4
• Wear protective gloves.
1. Remove the band saw blade (6) as described under
12.2.1.
2. Loosen the belt tensioning screw (29a) and press the
motor (16) slightly upwards to slacken the belt (29)
and tighten the belt tensioning screw (29a) slightly.
Use a 6 mm Allen key (E).
3. Dismantle the band wheel circlip (33).
Use circlip pliers*.
4. Remove the lower band wheel (25) from the band wheel
shaft (34) and remove the worn belt (29) from the band
wheel pulley (31) and the drive belt pulley (30).
5. Place the new belt (29) over the drive belt pulley (30).
6. Attach the lower band wheel (25) to the band wheel
shaft (34) and place the belt (29) over the band wheel
pulley (31).
7. Place the belt (29) on the desired drive belt pulley (30)
and on the parallel running band wheel pulley (31) (S1
or S2).
Ensure that the notches interlock and that the belt (29)
is centred on the drive belt pulley (30) and the band
wheel pulley (31).
8. Press the motor (16) slightly backwards and tighten
the belt tensioning screw (29a) on the motor (16)
again to tension the belt (29).
Use a 6 mm Allen key (E).
9. Fit the band saw blade (6) as described under 12.2.1.
* = may not be included in the scope of delivery!

13 Storage and transport

WARNING
Danger of injury and burning!
The product can start unexpectedly and cause injuries.
– Switch off the engine before carrying out any clean-
ing or maintenance work.
– Allow the engine to cool down.
– Pull out the mains plug.
• Empty the product completely.
• Clean and check the product for damage.
www.scheppach.com
Replacing the belt (29) (Fig. 17, 24)
GB | 39