Troubleshooting - Scheppach Hbs261 Originalbetriebsanleitung

Notes on the electrical and electronic equipment act
[ElektroG]
Waste electrical and electronic equipment
does not belong in household waste, but must
be collected and disposed of separately!
• Used batteries or rechargeable batteries that are not
installed permanently in the old appliance must be re-
moved non-destructively before disposal! Their dis-
posal is regulated by the battery act.
• Owners or users of electrical and electronic devices
are legally obliged to return them after use.
• The end user is responsible for deleting their personal
data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that
waste electrical and electronic equipment must not be
disposed of with household waste.
• Waste electrical and electronic equipment can be
handed in free of charge at the following places:
– Public disposal or collection points (e.g. municipal
works yards)

17 Troubleshooting

Fault
Motor does not work
The engine runs slowly and
does not reach the operating
speed.
Engine producing excessive
noise.
The engine does not reach full
power.
Motor overheats easily.
Saw cut is rough or wavy.
Workpiece pulls away and/or
splinters.
Band saw blade drifting.
Burn marks on the wood when
working.
Band saw blade jams when
working.
Motor runs but saw blade does
not move
Possible cause
Motor, cable or plug defective,
mains fuses blown,
both safety switches are not cor-
rectly engaged.
Voltage too low, coils damaged,
capacitor burnt.
Coils damaged, motor defective.
Circuits in the network are over-
loaded (lamps, other motors, etc.).
Overloading of the motor, insuffi-
cient cooling of the motor.
Band saw blade dull, tooth shape
not appropriate for the material
thickness.
Excessive cutting pressure and/or
band saw blade not suitable for use.
• Band saw blade guide poorly
adjusted.
• Incorrect band saw blade.
• Band saw blade blunt.
• Incorrect band saw blade.
• Band saw blade blunt.
• Band saw blade resinous.
• Band saw blade guide poorly
adjusted.
Belt is not
correctly tensioned
www.scheppach.com
– Points of sale of electrical appliances (stationary
and online), provided that dealers are obliged to
take them back or offer to do so voluntarily.
– Up to three waste electrical devices per type of de-
vice, with an edge length of no more than 25 centi-
metres, can be returned free of charge to the man-
ufacturer without prior purchase of a new device
from the manufacturer or taken to another autho-
rised collection point in your vicinity.
– Further supplementary take-back conditions of the
manufacturers and distributors can be obtained
from the respective customer service.
• If the manufacturer delivers a new electrical appliance
to a private household, the manufacturer can arrange
for the free collection of the old electrical appliance
upon request from the end user. Please contact the
manufacturer's customer service for this.
• These statements only apply to devices installed and
sold in the countries of the European Union and which
are subject to the European Directive 2012/19/EU. In
countries outside the European Union, different regu-
lations may apply to the disposal of waste electrical
and electronic equipment.
Remedy
Arrange for inspection of the product by a special-
ist. Never repair the motor yourself. Danger! Check
mains fuses, replace if necessary, engage both
safety switches correctly
Have an electrician check the voltage. Arrange for
inspection of the motor by a specialist. Arrange for
replacement of the capacitor by a specialist.
Arrange for inspection of the motor by a specialist.
Do not use any other products or motors on the
same circuit.
Avoid overloading the motor while cutting, remove
dust from the motor in order to ensure optimal cool-
ing of the motor.
Resharpen band saw blade or insert suitable band
saw blade.
Insert suitable band saw blade.
• Adjust the band saw blade guide.
• Insert suitable band saw blade.
• Replace the band saw blade.
• Insert suitable band saw blade.
• Replace the band saw blade.
• Clean the band saw blade.
• Adjust the band saw blade guide.
Retighten belt
GB | 41