Before Starting The Equipment; Technical Data - Scheppach Ps150-18Li Originalbetriebsanleitung

manufacturer will be liable for any damage or injuries
of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
Remaining hazards
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Wear regulation safety gear such as safety boots
and tight work clothing.
• Electrical hazards exist when unsuitable electric
connections are used.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz-
rds.
• Minimize remaining hazards by following the in-
structions in "Safety Rules", "Use only as author-
ized" and in the entire operating manual.

Technical data

Pole saw
Technical data
Data pole saw
Bar length mm
Cutting length mm
Guide bar typ
chain pitch
Saw chain type
Chain link thickness "
Oil
Pruner length min./
max. cm
Power unit
Nominal Voltage
Weight with battery kg
Weight without
battery kg
Noise and vibration
The noise and vibration values were developed us-
ing a standardised measuring process.
Sound pressure L
pA
Sound power L
wA
Uncertainty K
WA
Vibration A
hv
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
24 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
240
150
080SDEA041
3/8"
91P033X
1,3
Chainsaw oil
178 - 275
18 V
4,4
3,8
70,2 dB(A)
86,55 dB(A)
3 dB(A)
0,695 m/s²
1,5 m/s²
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves

Before starting the equipment

Unpack the device and check it for complete delivery
contents and transport damage.
NOTE
The batteries (optional; depending on the delivery
scope) are not fully charged on delivery. Before first
use, fully charge the batteries. See charger instruc-
tion manual.
Removing / inserting the battery
1. To remove the battery from the appliance, press
the release button on the battery and pull out
the battery.
2. To insert the battery , place it on the guide track
and push it back into the appliance. It will audi-
bly snap in.
Assembly of the shoulder strap (Fig. 2)
Hook the fastener of the shoulder strap into
the shoulder strap attachment .
Assembly of the cutter rail and the saw
chain
Take off the chain wheel cover. • Lay the chain as
shown in the groove which runs around the cutter rail
• Insert the cutter rail and chain as shown in the
mounting in the chainsaw . At the same time guide
the chain around the chain
wheel and hook the cutter rail into the chain tension-
ing bolt.
Assembly / disassembly the saw head. (Fig. 12)
To assemble the head, place the saw unit as shown
in Fig. No. 12 on the telescope unit. You have to
place the saw unit at an angle in order to be able to
insert the unit in the form lock. Look at both surfaces
first. Then squeeze the two components together.
Then turn the head until it snaps into place (item 17).
Now the pruner is operational.
If you want to disassemble the saw head, simply
slide down the splitter (Pos.17) and turn the head
until you can loosen the unit.
Assembly of telescopic rod and handle (Fig. 10
+ 11)
Push the telescopic rod and the handle together. The
guide prevents incorrect installation. Then screw the
locking nut (Pos.14) together with the thread of the
handle