Koenic KRVC 2320 RC Gebrauchsanweisung Seite 22

Size - A5
English
Set time
Fig. 11 Press the on/ standby button on the
Fig. To use the timer, the time must be set
8 device or the start/ pause button on
on the remote control.
the remote control to start the cleaning
Press the time button. The hour process. The LED of the on/ standby
indicator flashes. Now set the hours button shines permanently.
with the aid of the arrow keys . Press the on/ standby button on the
Then press the key to set the unit or the start/ pause button on the
minutes display. The minute display remote control again to pause the
flashes. Use the arrow keys to cleaning process. Press the on/ standby
set the minutes. Confirm your entry by button on the unit or the start/ pause
pressing the time button. The time is
button on the remote control again if
now set.
you want to continue cleaning.
However, if you do not press a button
within approx. 60 seconds, the vacuum
Operation as a vacuum cleaner robot will switch to the standby mode.
In standby mode, the LED is o. To
activate the vacuum robot press the
Warning!
on/ standby button on the device or
• To prevent damage, make sure that any the start/ pause button on the remote
loose items, such as curtains, clothing, control.
paper, cables, and extension cords, have The vacuum robot will automatically
been removed from the floor.
return to the charging base, after the
• Loose cables can get caught in the vacuum
cleaning task has been finished or
robot during operation and be pulled
when the battery is almost empty. If
along by it, which can cause considerable
the robot is used in a dierent room,
damage and possibly can also cause a fire. it has to be placed in front of the
Place cables and sockets in such a way
charging base and the charging base
that they cannot get in contact with the button on the remote control or the
vacuum robot. button on the device has to be pressed.
Note:
Fig. When the battery level is low, the
12
• Each time a key is pressed, an
robotic vacuum automatically returns
announcement sounds in English.
to the charging station. When returning
• Make sure the dust container is clean and
to the charging station, the cleaning
the filters are properly inserted. Please
process is interrupted.
note the chapter Cleaning and care .
Clean the suction opening regularly
with the appliance switched o (on/
Fig. 9 Make sure, that the on/o switch on
o switch in position ) and empty O
the under-site of the robot is in the on- the dust container and the pre-filter
position.
after each use. Please note the chapter
Cleaning and care.
Fig. It is possible to start the cleaning
10
process, while the robot is situated on
the charging base as well as when it's
positioned in the middle of the room. In
both cases, use the remote control or
the button on the device, to start the
cleaning process.
22
IM_KRVC2320RC_190807_V10_HR.indb 22
Set start time with timer
Fig. To start a cleaning process in your
13
absence, set a start time for cleaning.
Note: You must be near the robot vacuum
cleaner with the remote control. If the blue
LED is o when the timer settings are
completed (sleep/ standby mode), the start
time settings will not be applied.
Set the on/ o switch to position and press I
the on/ standby button on the unit or the start/
pause button on the remote control. The device
is now activated. Press the timer button to set
the start time.
The hour indicator flashes. Use the arrow keys
to set the hours. Then press the arrow
key to set the minutes display.
The minute display flashes. Use the arrow
keys to set the minutes.
Confirm your entry by pressing the timer
button. An acoustic signal sounds and indicates
that the vacuum cleaner has been successfully
pre-programmed.
The LED of the control lamp flashes. At the set
time, the cleaning process starts.
To deactivate the start time, press the Timer
button for approx. 3 seconds. The timer symbol
in the display o the remote control turns o.
7/8/2019 14:43