Battery Removal/Installation - Hitachi WH 18DDL Bedienungsanleitung

English
APPLICATION
Driving and removing of machine screws, wood screws, tapping screws,
self drilling screws, etc

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch to remove the battery (see
Fig. 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see Fig. 2).
Before
charging
While
charging
Charging
complete
The pilot
lamp lights
or blinks.
Charging
impossible
Overheat
standby
(2) Regarding the temperatures of the rechargeable battery
The temperatures for rechargeable batteries are as shown in Table 2, and
batteries that have become hot should be cooled for a while before being
recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
BSL1430, BSL1440, BSL1450
BSL1830, BSL1840, BSL1850
(3) Regarding recharging time
Depending on the combination of the charger and batteries, the charging
time will become as shown in Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery
BSL1430, BSL1830
BSL1440, BSL1840
BSL1450, BSL1850
NOTE
The charging time may vary according to temperature and power source
voltage.
11
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5 seconds.
Blinks
(off for 0.5 seconds)
(red)
Lights continuously
Lights
(red)
Lights for 0.5 seconds. Does not light for 0.5 seconds.
Blinks
(off for 0.5 seconds)
(red)
Lights for 0.1 seconds. Does not light for 0.1 seconds.
Flickers
(off for 0.1 seconds)
(red)
Lights
Lights continuously
(green)
〈UC18YRSL〉
Blinks Lights for 1 seconds. Does not light for 0.5 seconds.
(off for 0.5 seconds)
(red)
〈UC18YFSL〉
Temperatures at which the
battery can be recharged
0°C – 50°C
UC18YRSL / UC18YFSL
Approx. 45 min.
Approx. 60 min.
Approx. 75 min.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to a receptacle. When the power cord is
connected, the charger's pilot lamp will blink in red. (At 1-second intervals)
2. Insert the battery into the charger.
Firmly insert the battery into the charger, as shown in Fig. 3, 4.
3. Charging
When inserting a battery in the charger, charging will commence and the
pilot lamp will light continuously in red.
When the battery becomes fully recharged, the pilot lamp will blink in red.
(At 1-second intervals) (See Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in Table 1, according to
the condition of the charger or the rechargeable battery.
Table 1
4. Disconnect the charger's power cord from the receptacle.
5. Hold the charger firmly and pull out the battery.
NOTE
After operation, pull out batteries from the charger first, and then keep the
batteries properly.
Regarding electric discharge in case of new batteries, etc.
As the internal chemical substance of new batteries and batteries that have
not been used for an extended period is not activated, the electric discharge
might be low when using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will be restored by
recharging the batteries 2-3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become completely exhausted.
When you feel that the power of the tool becomes weaker, stop using the
tool and recharge its battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life will become
shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use. If such a battery is
recharged immediately after use, its internal chemical substance will
deteriorate, and the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
Malfunction in the battery or the
charger
Battery overheated.
Unable to charge. (Charging will
commence when battery cools)