Novoferm tormatic T100 R-FU 1,5kW Montage- Und Betriebsanleitung Seite 31

Menu 4 Further door settings
Menu Entry Selection
item
43 Floor adjustment
0 off (default setting)
1 on
44 Hold-open time in seconds
0 0 s (default setting)
1 - 30 1 s - 30 s (in increments of 1 s)
31 - 60 35 s - 180 s (in increments of 5 s)
61 - 99 190 s - 22.5 min (in increments of 30 s)
45 Status relay X5
0 Door close signal (default setting)
1 Door open signal
2 Status of door for traffic light control A800
3 2-minute garage light
4 5-minute garage light
5 On / off with hand-held transmitter (menu
item 62)
6 ELTACO wipe pulse
46 Status relay X6
0 Door close signal
1 Door open signal (default setting)
2 Status of door for traffic light control A800
3 Locking
4-14 Warning light closing (0 - 10 s warning time)
15-25 Warning light opening and closing (0 s - 10 s)
48 Force detection settings
0 Force detection inactive
1-99 Force detection cycle active, permissible over-
current 101-199 % of the current measured dur-
ing the force learning cycle.
The following values can be used as
a guide:
Settings for spring-balanced doors (approx.
200 kg)
20 – very high sensitivity
25 – high sensitivity (approx. 20 kg)
40 – medium sensitivity
60 – low sensitivity
Settings for heavy spring balanced doors
(approx. 450 kg)
8 – very high sensitivity
9 – high sensitivity (approx. 20 kg)
13 – medium sensitivity
21 – low sensitivity
Settings for heavy springless doors (ap-
prox. 320 kg)
2 – very high sensitivity
5 – high sensitivity (approx. 20 kg)
6 – medium sensitivity
7 – low sensitivity
Settings for heavy springless doors (ap-
prox. 380 kg)
2 – very high sensitivity
6 – high sensitivity (approx. 20 kg)
7 – medium sensitivity
8 – low sensitivity
Default value: 20
Menu 4 Further door settings
Menu Entry Selection
item
49 Motor duty cycle
0 Without limitation (default setting)
1 Geared motor 5.24 (25 min / 35 %)
2 Geared motor 5.24 WS (25 min / 30 %)
3 Geared motor 9.15, 9.20, 9.24 (25 min / 60 %)
4 Geared motor 9.24 WS (25 min / 20 %)
5 Geared motor 6.65 DU (10 min / 35 %)
6 Geared motor 14.15 (25 min / 60 %)
- - Exit menu
Menu 5 Various settings
Menu Entry Selection
item
50 Key switch function (J7)
0 Pulse input OPEN/CLOSE (default setting)
1 Inhibit control panel
2 Inhibit external control elements
3 Inhibit control panel and external control elements
4 Activate control elements for 10 seconds
5 Switch-over to dead man mode for closing
6 Switch-over to 1/2 opening (winter mode)
7 Pulse input OPEN-STOP-CLOSE
8 Pulse input 1/2 OPEN-STOP-CLOSE
9 Automatic closing AR
10 Pulse input for smoke and heat extraction sys-
tem (setting in menu item 55)
11 Pulse input for smoke and heat extraction sys-
tem, inverted (setting in menu item 55)
12 Mutual locking of door
51 Function of external control devices
0 off (default setting)
1 Dead man open / dead man close
2 Pulse open / dead man close
3 Pulse open / pulse close
4 Pulse 1/2 door opening / pulse close
5 AR operation, automatic closing
6 AR operation, 1/2 door opening
7 Open-close operation
8 Open / close pulse as NO contact
52 001-256 Entry of control address
53 Plug-in module
0 off (default setting)
1, 2, 3, 4 DC module
5 RSE system with OSE
6 RSE system with 8k2
55 Door setting for smoke and heat extraction sys-
tem position
58 RSE selection of wicket door contact
Press for 5 s: delete pairing of RSE-system
0 ENS-8200
1 ENS-S 68xx (default setting)
2 NC contact
- - Exit menu
T100 R-FU 1,5kW EN - 29