Function Menu - Retevis Rt95 Bedienungsanleitung

Channel Scan
In channel mode, this function is designed to monitor signal of all channel.
1. In channel mode, press [FUNC] key to switch function group, choose the [PX] key defined as SCN function.
2. Short press the [PX] key defined as SCN function to start channel scan, the LCD displays: S.
3. Turn channel knob or press microphone [UP][DOWN] key can change scan direction.
4. Turn channel knob or press any key except microphone [UP]/[DOWN] key to exit.
5.15 Scan Skip
In channel mode, press [FUNC] key to switch function group, choose the [PX] key defined as SCN function. Hold this key to
add into or delete from scan list.
1. When LCD displays:S, the current channel is in scan list.
2. When LCD not displays:S, the current channel is not in scan list.
5.16 Squelch off/ Squelch off Momentary
The [PX] key defined as MON function, can monitor the weak signal.
1. Press [FUNC] key to switch function group, choose the [PX] key defined as MON function.
2. Short press the [PX] key defined as MON function to turn squelch off / squelch off momentary, the LCD displays red "RX"
icon.
Squelch off: press the [PX] key defined as MON to disable squelch, press [MON] key to resume squelch.
Squelch off momentary: hold the [PX] key defined as MON to disable squelch, release [MON] key to resume squelch.
5.17 KEYPAD LOCKOUT
Avoiding unintentional operation, this function will lock the keys except [PTT], [PUSH], Keys.
1. Long press [PUSH] button, the downside of the LCD displays Key Lock, means the keypad is locked.
2. Long press [PUSH] button again, the downside LCD displays : Key Unlock, means the keypad is unlocked.
» NOTE:When keypad lockout, except key, [PUSH] button and [PTT] key is available, other keys are invalid .
5.18 Transmit DTMF/5 Tone Signaling
If the current channel is with DTMF/5TONE signaling, hold PTT and [UP] key will transmit selected Pre-programmed signaling.
5.19 Transmit Tone burst frequency
Hold PTT and [DOWN] key will transmit selected Pre-programmed tone burst frequency.
5.20 Transmit DTMF by Microphone Keypad
Hold PTT, then input DTMF signaling by the microphone keypad.

6. FUNCTION MENU

1. Hold [FUNC] key to enter SELECT MENU interface.
2. Short press [P4], [P6] key or turn channel knob to choose menu list. Short press [P5] can fast turn page.
3. Press [PUSH] button to enter FUNC MENU setting.
4. Short press [P4], [P6] key or turn channel knob to choose wanted setting.
6.1 Beep
1. Enter FUNCTION MENU list, choose No.01 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting. Off~5: 6 levels available. Off: Turn off BEEP function.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.2 Frequency Step Size Setup
1. Enter FUNCTION MENU list, choose No.02 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
Total 9 Channel step size available: 2.5K,5K,6.25K,10K,12.5K,20K,25K, 30K and 50K.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.3 Display mode setup
This radio has 3 different display: Frequency+Channel and Channel name Tag mode.
1. Enter FUNCTION MENU list, choose No.03 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
FRQ: Frequency+Channel mode.
CH: Channel mode.
NM: Channel+name mode+ Channel mode, If channel not named, it displays
Fequency + Channel mode, otherwise displays the channel name.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.4 Squelch level Setup
This function use for setting RX signal strength, the calling will be heard only when reach setted level, otherwise the radio
will keep mute.
9