Talk Around - Retevis Rt95 Bedienungsanleitung

» 5Tone group name and connect shall be programmed by PC software. If the choose 5Tone encode has a group
name, the LCD will display group name only.
7.5 T-DEC (Add Optional Signaling)
This transceiver has 2 optional signaling: DTMF/5Tone/. those signaling function similar to CTCSS/DCS signaling. When
the receiver adds an optional signaling, the caller shall transmit matching signaling. DTMF and 5Tone signaling can be
applied for other advanced features such as ANI, PTT ID, group call, select call, remotely stun, remotely kill waken...etc.
1. Enter CHAN MENU, choose No.4 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
DT: means DTMF signaling is added.
5T: means DTMF signaling is added.
OFF: Turn off optional signaling.
4. Press [PUSH] button or [P3] key to store setting and exit.
» The working of optional signaling shall be work associated with the squelch mode setup. (Refer to Squelch Mode
setup in page XX ).
7.6 Signaling Combination Setup
This function can improve the level of blocking irrelative signals.
1. Enter CHAN MENU, choose No.6 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
SQ:You can hear the calling when receive a mathcing carrrier.
CDT:You can hear the calling when receive a matchng carrier and CTCSS or DCS signaling.
TONE: You can hear the calling when receives matching carrier + optional signaling.
C&T: You can hear the calling when receives matching carrier + CTCSS/DCS + optional signaling.
C/T: You can hear the calling when receives any matching carrier or CTCSS/DCS or optional signaling.
4. Press [PUSH] button or [P3] key to store setting and exit.
» This settting is valid only when CTCSS/DCS signaling added.
7.7 Band-width Selection
Select suitable bandwidth in accordance with different local conditions
1. Enter CHAN MENU list, choose No.7 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
WID: band width is 25k(Wide band)
MID: band width is 20k(Middle band)
NAR: band width is 12.5k(Narrow band)
4. Press [PUSH] button or [P3] key to store setting and exit.
7.8 Frequency Reverse
With this function on, the transceiver will be able to communicate with a transceiver in
same network without through a repeater.
1. Enter CHAN MENU list, choose No.8 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
ON: Turn on reverse function
OFF: Turn off reverse function
4. Press [PUSH] button or [P3] key to store setting and exit
» Frequency reverse is turn on, the TX and RX frequency will be exchanged, the CTCSS or DCS signaling also will
be exchanged if existed in current channel.

7.9 Talk Around

1. Enter CHAN MENU list, choose No.9 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting
ON: Turn on talk around function
OFF: Turn off talk around function
4. Press PUSH button or P3 key to store setting and exit.
» This function is hide when RTDF function is on.
7.10 Offset Freqeuncy And Direction Setup
1. Enter CHAN MENU list, choose No.10 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting, press [FUNC] key to set the offset direction.
-: Minus offset, means transmitting frequency lower than receiving frequency.
+: Plus offset, means transmitting frequency higher than receiving frequency.
OFF: OFFSET is turn off.
13