Retevis RT95 Bedienungsanleitung Seite 10

2.Short press [PX] key defined as A/B function, then repratedly press this key or turn channel knob to switch main channel
and sub channel, the LCD displays Main:XX.
3. Hold [PUSH] or [FUNC] key to store and exit, or wait 10 seconds the radio will store the setting and exit.
5.8 Switch between VFO and Channel Mode
1. Short press [FUNC] to switch function group, choose the [PX] key defined as V/M function.
2. Short press [PX] key defined as V/M function, then repeat press this key or turn channel knob to switch main channel and
sub channel, the LCD displays V/M:XX.
3. Hold [PUSH] or[FUNC] key to store and exit, or wait 10 seconds the radio will store the setting and exit.
5.9 Channel Edit
1. In VFO mode, turn channel knob or the [UP]/[DOWN] key in microphone to adjust frequency.
2. Short press [FUNC] to switch function group, choose the [PX] key defined as CDT function. Press [PX] key defined as
CDT function to set CTCSS/DCS code. turn channel knob or the [UP]/[DOWN] key in microphone to choose CTCSS/DCS
code.
3. Long press [FUNC] key to enter channel setting menu, to choose wanted setting.
4. Short press [FUNC] key to switch function group, hold the [PX] key defined as V/M function until the channel number
flashes,if the channel number is red means current channel is valid, if the channel number is green, means current channel
is empty.
5. Turn the channel knob or microphone [UP]/[DOWN] key to choose the channel number to be stored.
6.Hold the [PX] key defined as V/M function to confirm and store the channel ,the channel number stop flash and radio
emits a beep sound,the channel is stored successfully.
5.10 Channel Delete
1. In channel mode, turn the channel knob or microphone [UP]/[DOWN] key to choose an unwanted channel.
2.Short ptess [FUNC] key to switch function group,choose the [PX] key defined as V/M function, press this key together with
[FUNC] key for 2 seconds, current channel is
deleted and automatical jump to next channel.
5.11 CTCSS/DCS Encode and Decode Setup
1. Short press [FUNC] to switch function group, choose the [PX] key defined as CDT function.
2.Short press PX defined as CDT function,then repearedly short press this key set the currently channel if use CTCSS/DCS
encode and decode.
3. When the LCD displays: RCDT:XXX, turn channel knob or press microphone [UP]/[DOWN] key to choose if add CTCSS/
DCS decode signaling to current channel. Press [PUSH] button then turn channel knob or press microphone [UP]/[DOWN]
key to choose wanted CTCSS/DCS decode signaling.
4. When the LCD displays: TCDT:XXX, turn channel knob or press microphone [UP]/[DOWN] key to choose if add CTCSS/
DCS encode signaling to current channel. Press [PUSH] button then turn channel knob or press microphone [UP]/[DOWN]
key to choose wanted CTCSS/DCS encode signaling.
5.CTCSS:62.5-254.1Hz plus one self define group. total 52 group.
DCS: 000N-777I total1024 groups.
N is positive code, I is inverse code.
Press FUNC key can choose positive or inverse code.
6. Hold [PUSH] or [FUNC] key to store and exit, or wait 10 seconds the radio will automatically store the setting and exit.
» Under channel mode,this operation can be temporarily used by user. Once the radio is turned off or switched to
another channel, the temporary setting will be erased. If the channel setting programmed for valid, the temporary
setting will keep valid until next change, turn off radio or switch to another channel, the temporary setting will not
changed.
5.12 CTCSS Scan
In channel or VFO mode, short press [FUNC] to switch function group, choose the [PX] key defined as CDT funtion.short
press this key to enter CTCSS code setting.when the LCD displays CTC, long press this key to enter CTCSS scan. turn
channel knob or press microphone [UP]/[DOWN] key can change scan direction.Once finding a matching CTCSS signaling,
it will stop 5 seconds then scan again, short press any key to exit CTCSS scan.
5.13 DCS Scan
In channel or VFO mode, short press [FUNC] to switch function group, choose the [PX] key defined as CDT function. short
press this key to enter DCS code setting. When the LCD displays DCS, long press this key to enter DCS scan, turn channel
knob or press microphone [UP]/[DOWN] key can change scan direction. Once finding a matching DCS signaling, it will stop
5 seconds then scan again, press any key to exit DCS scan.
5.14 Frequency/Channel Scan
Frequency Scan
In frequency (VFO) mode, this function is designed to monitor signal of all frequency points under each step size.
1. In VFO mode, short press [FUNC] key to switch function group, choose the [PX] key defined as SCN function.
2. Short press the [PX] key defined as SCN function to start frequency scan, the LCD displays "S".
3. Turn channel knob or press microphone [UP[DOWN] key can change scan direction.
4. Turn channel knob or press any key except microphone [UP][DOWN] key to exit.
8