Retevis RT95 Bedienungsanleitung Seite 12

1. Enter FUNCTION MENU list, choose No.04 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
Off-9: Total 10 levels, OFF is lowest level, squelch is off.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.5 Volume level setting
1. Enter FUNCTION MENU list, choose No.05 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
1-36: total 36 levels available.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.6 Password setting
After enable this function, must be input correct password then can turn on the transceiver.
1. Enter FUNCTION MENU list, choose No.06 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
ON: Turn on password function.
OFF: Turn off password function.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.7 Scan Dwell Time Setup
1. Enter FUNCTION MENU list, choose No.07 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
TO: It pause for preset pause time when scanning a matching signal, then resume scan.
CO: It pauses once scanning a matching signal, and resume scan when signal disappears.
SE: It stops once scanning a matching signal.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.8 Scan Pause Time Setup
1. Enter FUNCTION MENU list, choose No.08 function .
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
5S : It pauses 5s once scanning a matching signal, then resume scan.
10S : It pauses 10s once scanning a matching signal, then resume scan.
15S : It pauses 15s once scanning a matching signal, then resume scan.
Press [PUSH] button or [P3] key to store setting and exit.
6.9 AOP (Automatic power on setup)
When turn off AOP, the radio need press key to power on when connect with the power supply.
1. Enter FUNCTION MENU list, choose No.09 function.
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting.
ON : Enable AOP function.
OFF: Power off by manual.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.10 Dual Watch setup
1. Enter FUNCTION MENU list, choose No.10 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose wanted setting
ON: Enable Dual Watch function
OFF: Disable Dual Watch function
4. Press [PUSH] button or [P3] key to store setting and exit.
6.11 Backlight Brightless Setup
1. Enter FUNCTION MENU list, choose No.11 function
2. Press [PUSH] button, the menu value in LCD turns to green color.
3. Turn channel knob to choose brightless level, 1-3 level available.
4. Press [PUSH] button or [P3] key to store setting and exit.
6.12 TOT(Time Out Timer)
The time-out timer limits continuous transmitting time. When transmit time last over
programmed value, the transmitting will stop and emit a prompt.
1. Enter FUNCTION MENU list, choose No.12 function
2. Press [PUSH] button, the menu value in LCD turns to green color
3. Turn channel knob to choose wanted setting.
1-30: 1-30 minutes range available by 1 minute/step
10