Working Mode; Basic Operations - Retevis Rt95 Bedienungsanleitung

B. Channel Name Mode: When set display as "Name",it enters into Channel
name mode. In this mode,it will display corresponding channel name when the
current channel is edited with name. Otherwise, it will display frequency +
channel number.(As pic 2)
C. Channel mode: When set display mode as "Channel" , it enters channel mode.
If there is name for current channel , the LCD will display current channel name
otherwise it shows current channel number.(As pic 3)

2. Working Mode

How to choose work mode by PC programming: In PC software's "Function Setup" menu, the "VFO/MR A" and "VFO/MR B"
selection available setting: "VFO","MR.".
A. VFO Mode: This mode shows only frequency on the display. Shortcut operation and Channel setting will be changed &
stored as the latest value. if the radio is turned off,the latest setting will not changed.In VFO mode, adjust the channel knob
will adjust the frequency by pre-programmed step size.
B. "MR." Mode: Memory mode, In this mode, the radio will work by pre-programmed channels, ajust the channel knob will
move the channel up and down.
» If transceiver programmed as channel mode and locked, you can't return to frequency mode by manual operation
in the radio menu.

5. BASIC OPERATIONS

5.1 Switching the Power On/Off
1. Power On: in power off state press
2. Power Off: in power on state, press
5.2 Adjusting the Volume
1. In standby mode, short press the [PX] key programmed as VOL control, the LCD display "VOL:XX", then turn the channel
switch to adjust volume level.
2. In standby mode, short press
volume level.
» During communication, volume level can be adjusted more accurate.
5.3 Adjusting Frequency
1. By channel knob: In VFO mode, turn channel knob can adjust frequency, push channel knob,the matching charactor will
flash,then turn channel knob to adjust the frequency by step size 1K, 10K, 100K, 1Mz or 10MHz.
» The microphone [UP]/[DOWN] key can also adjust the frequency, each press move one step size. hold the [DOWN]
key can decrease one step size. if the channel knob is programmed as VOL function, users need press the PX key
which programmed as FRQ function, when the LCD displays "VFO FREQ", turn channel knob to adjust frequency.
2. By number key: In VFO mode, you can input wanted frequency by the microphone number key. For example if want
145.125Mhz, just press key 1, 4, 5, 1, 2, 5, if want 145Mhz, just press 1, 4, 5. The input is invalid if the frequency is over
range.
5.4 Adjust Channel
1. Adjust channel by channel switch: In channel mode, turn channel knob to adjust the channel, the [UP]/[DOWN] key in the
microphone can also adjust the main channel.
» If there is an empty channel, the radio will jump over it to next channel. If the channel knob is programmed as VOL
function, users need press the PX key which programmed as CH function, when the LCD displays "CH XX ", turn
channel knob to adjust channel.
2. By number key: In CH mode, you can input wanted channel by the microphone input 3 numbers (001-200) , 001 stands
for channel 1, 200 stands for channel 200. if input channel is an empty channel, the radio will report error and return to last
channel.
5.5 Receiving
When the channel you are operating being called, the screen shows red RX and field strength in this way you can hear the
calling.
» When the RX icon and field strength flashes,but can not hear the calling,it means current channel receive a
matching carrier but unmatching signaling. Refer to CTCSS/ DCS CODE or Optional Signaling setup in Page 14).
5.6 Transmitting
Hold [PTT] and speak into microphone. the radio start transmit, the screen shows red TX and field strength.Hold the
microphone approximately 2.5-5.0cm from your lips and speak to microphone in your normal speaking voice to get best
timbre.
» Only available transmit on main channel.
5.7 Switch between Main Channel and Sub Channel
This radio work by single channel dual watch , in standby, the frequency in the upper side is main channel and down side is
sub channel, the transmit is available only on main channel.
1. Short press [FUNC] to switch function group, choose the [PX] key defined as A/B function.
, the LCD displays " RETEVIS " then willdisplays current frequency or channel.
for 2 seconds, the LCD displays "CLOSING",then the LCD display disappears.
to mute the speaker, the LCD display "AUDIO:MT",short press it again to return last
7
(As pic 2) (As pic 3)