Scheppach BS251 Original Bedienungsanleitung Seite 27

– When processing wood, materials similar to
wood, and plastics. operation in enclosed spac-
es is only permitted with the use of a suitable
extraction system.
11 Do not use the cable for purposes for which it is
not intended
– Do not use the cable to pull the plug out of
the outlet. Protect the cable from heat, oil and
sharp edges.
12 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. It is thus held more securely
than with your hand and allows the machine to
be operated with both hands.
– An additional support is necessary for long
workpieces (table, trestle, etc.) in order to pre-
vent the machine from tipping over.
– Always press the workpiece firmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
13 Avoid abnormal posture
– Make sure that you have secure footing and
always maintain your balance.
– Avoid awkward hand positions in which a sud-
den slip could cause one or both hands to come
into contact with the saw blade.
14 Take care of your tools
– Keep cutting tools sharp and clean in order to
be able to work better and more safely.
– Follow the instructions for lubrication and for
tool replacement.
– Check the connection cable of the power tool
regularly and have it replaced by a recognised
specialist when damaged.
– Check extension cables regularly and replace
them when damaged.
– Keep the handle dry, clean and free of oil and
grease.
15 Pull the connector out of the socket
– Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
– When the power tool is not in use or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
– If the saw blade jams during cutting due to
excessive feeding force, switch off the device
and disconnect it from the mains. Remove the
workpiece and make sure that the saw blade
runs freely. Switch the device on and carry out
the cutting operation again with reduced feed-
ing force.
16 Do not leave a tool key inserted
– Before switching on, make sure that keys and
adjusting tools are removed.
17 Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
18 Use extension cables for outdoors
– Only use approved and appropriately identified
extension cables for use outdoors.
– Only use cable reels in the unrolled state.
19 Always remain attentive
– Pay attention to what you are doing. Remain
sensible when working. Do not use the power
tool when you are distracted.
20 Check the power tool for potential damage
– Protective devices or other parts with minor
damage must be carefully inspected to ensure
that they function correctly and as intended
prior to continued use of the power tool.
– Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fulfilled to ensure fault-
free operation of the power tool.
– The moving protective hood may not be fixed
in the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any power tool on which the switch
cannot be switched on and off.
21 Attention!
– The use of other insertion tools and other ac-
cessories can entail a danger of injury.
22 Have your power tool repaired by a qualified elec-
trician
– This power tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
m WARNING! This power tool generates an elec-
tromagnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the power tool.
Additional safety instructions
• Wear protective gloves for all maintenance work
on the saw band!
• When cutting round timber, use a device to prevent
the workpiece turning.
• When cutting boards on edge, use a device to pre-
vent the workpiece kicking back.
www.scheppach.com
GB | 27