Resetting The Saturation Indicator; Home Connect; Safety - Gaggenau Ac250121 Gebrauchs- Und Montageanleitung

en Home Connect
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is saved
automatically.
A signal tone sounds as soon as the selected setting
is saved.
7.12 Saturation indicator
If the grease filters or odour filters are saturated, corres-
ponding symbols flash after the appliance is switched
off.
Note: You can set the saturation indicator in the
Home Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.13 Setting the saturation indicator
The saturation indicator must be adjusted depending on
the filter used.
Requirement: The appliance is switched off.
Press and hold and
1.
To set circulating-air mode (non-regenerable filter),
press / until LED 2 lights up in the LED display.
To set circulating-air mode (non-regenerable filter),
press / until LED 3 lights up in the LED display.
To convert the electronic control back to operation
without the air recirculation filter, press
LED 1 lights up on the LED display.
To save the setting, press and hold and for ap-
2.
prox. three seconds.
Or wait approx. 10 seconds until the setting is saved
automatically.
To cancel the setting, press .
A signal tone sounds as soon as the selected setting
is saved.
7.14 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
8 Home Connect
Home Connect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the Home Connect app, adjust its basic settings and
monitor its operating status.
The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services in
your country. You can find information about this at:
www.home-connect.com .
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
If the appliance is not connected to your home network,
it functions as an appliance with no network connection
and can still be operated via the display.
28
and for ap-
for approx. three seconds.
/ until
Requirements
After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation in-
dicator for the odour filter.
A signal sounds repeatedly.
Press .
The saturation indicator is reset.
7.15 Switching on the button tone
The button tones can be switched on.
Requirement: The appliance is switched off.
Press and hold and
1.
In the LED display, the LED for the setting that is cur-
rently selected lights up.
Press or until LED 1 lights up in the LED display.
2.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is saved
automatically.
A signal tone sounds as soon as the selected setting
is saved.
7.16 Switching the button tone off
The button tones can be switched off.
Note: Signal tones for the appliance are always
switched on and cannot be switched off.
Requirement: The appliance is switched off.
Press and hold and
1.
In the LED display, the LED for the setting that is cur-
rently selected lights up.
Press or until LED 2 lights up in the LED display.
2.
To cancel the setting, press .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is saved
automatically.
A signal tone sounds as soon as the selected setting
is saved.
Tip: Please also follow the instructions in the
Home Connect app.
Notes
Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Connect
app.
"Safety", Page 22
Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
In networked standby mode, the appliance requires a
maximum of 2 W.
for approx. three seconds.
and for ap-
for approx. three seconds.
and for ap-