Herunterladen Diese Seite drucken

Scheppach DP18VARIO Original Bedienungsanleitung Seite 32

Vorschau ausblenden Andere Handbücher für DP18VARIO:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
7.
Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, keep the packaging until the expiry of the
warranty period.
ATTENTION
The device and the packaging are not children's toys!
Do not let children play with plastic bags, films or small
parts! There is a danger of choking or suffocating!
8. Before commissioning
Before each use, always check:
• On/off switch incl. emergency stop switch for prop-
er function.
• Always carry out a visual inspection before use.
• Check safety devices, electrical controls, electrical
cables and screw connections in particular for dam-
age and firm seating. If necessary, replace damaged
parts before operating the machine.
• Make sure that the table clamping lever is tightened
before you start the machine.
• Make sure that the drill bit is securely fastened in
the chuck.
• Remove the chuck key from toothed chucks. Before
switching the device on, check whether the chuck
key has been removed.
9.
Assembly
Column and machine foot, Fig. 4
1.
Set the machine foot (1) down on the ground or the
workbench.
2.
Place the column (2) on the base plate so that the
holes on the column (2) align with the holes on the
base plate (1).
3.
Screw the four hexagonal bolts (23) to fasten the
column into the base plate and tighten them using a
hexagon spanner (A).
Assembling the drilling table, Fig. 7
1.
Insert the drilling table (4) into the drilling table
holder (22).
2.
Use a clamping handle (3) to secure the drilling
table (4).
32 | GB
Installing the machine head and column, Fig. 8
1.
Place the machine head (17) on the column (2).
2.
Align the drill's spindle with the table and the base
plate and tighten the Allen screws that are located
on the side of the machine head. (Allen key, AF4 / C)
Installing the handle, Fig. 9+10
1.
Screw three handles (10) tight in the handle bracket's
thread. Use the hexagon spanner (A) to do this.
2.
Screw the speed adjustment lever (6) into the han-
dle bracket for speed adjustment. Use the hexa-
gon spanner (A) to do this.
Installing the folding swarf protector and the drill
chuck, Fig. 11+12+13
1.
Push the folding swarf protector (11) onto the spin-
dle on the machine head and use a Phillips head
screwdriver to secure it.
2.
Push the tapered mandrel (21) into the drill chuck
(12) with a sharp jolt.
3.
Then push the tapered mandrel (21) into the drill
spindle. To do this, guide the drill chuck (12) including
the cone (21) into the spindle until is reaches the stop
and then turn it until it slides a little further into the
spindle. Now insert the drill chuck (12) including the
cone into the spindle. Check that it is tight.
Note: To protect against corrosion, all bare parts are
heavily greased at the factory. Before mounting the drill
chuck (12) on the spindle, both parts must be cleaned
with an environmentally friendly solvent to remove all
grease to ensure optimal power transmission.
Setting up the machine (Fig. 26)
Before use, the drill must be mounted in a stationary posi-
tion on a firm surface. Use the two fastening holes (26) in
the base plate for this. Make sure that the machine is free-
ly accessible for operation, adjustment and maintenance.
Note: The fastening screws must only be tightened so
that the base plate is not strained or deformed. Exces-
sive use can cause the device to break.
Please note before commissioning
Make sure that the voltage of the mains connection match-
es that on the type plate. Only connect the machine to a
socket with a properly installed protective contact. The drill
is equipped with a zero voltage trigger that protects oper-
ators from unintentional restarts after a power outage. In
this case, the machine must be switched on again.
www.scheppach.com

Werbung

loading

Diese Anleitung auch für:

5906807901