Weller WX 1 Originalbetriebsanleitung Seite 16

For your safety
Soldering and desoldering
ωКrrв Шut sШХНОrТЧР аШrФ Кs НТrОМtОН ТЧ tСО ШpОrК-
tТЧР ТЧstruМtТШЧs ШП вШur МШЧЧОМtОН sШХНОrТЧР tШШХέ
Handling the soldering tips
„
Coat the selective and tinnable soldering tip with
sШХНОr аСОЧ СОКtТЧР Тt up ПШr tСО irst tТЦОέ TСТs
removes oxide coatings which have formed
during storage and impurities from the soldering
tip.
„
Make sure that the soldering tip is well coated
with solder during breaks between soldering work
and prior to storage of the device.
ϊШ ЧШt usО КРРrОssТvО luбТЧР КРОЧtsέ
„
χХаКвs ЦКФО surО tСКt tСО sШХНОrТЧР tТps КrО
„
ittОН prШpОrХвέ
„
Select as low a working temperature as possible.
„
Select the largest possible soldering tip shape for
the application.
RuХО ШП tСuЦЛμ tСО sШХНОrТЧР tТp sСШuХН ЛО rШuРСХв
as large as the soldering pad.
„
Coat the soldering tip well with solder to ensure
WX 2, WXD 2, WXA 2: Overload cut-out (255 W)
To avoid overloading a WX station, one channel
Тs КutШЦКtТМКХХв НОКМtТvКtОН ТП tСО pШаОr Шutput
of both tool channels is greater than 255 watt
(Auto-Off).
Equipotential bonding
32
www.valuetronics.com
όШur vКrТКЧts КrО pШssТЛХО Лв МШЧЧОМtТЧР tСО γέη ЦЦ УКМФ sШМФОt
НТППОrОЧtХвμ
a
a Hard-grounded
b
b Equipotential
bonding
c
c Floating
d Soft-grounded
d
tСКt tСОrО Тs ОПiМТОЧt СОКt trКЧsПОr ЛОtаООЧ tСО
soldering tip and the soldering area.
„
Prior to extended breaks between soldering work,
sаТtМС ШПП tСО sШХНОrТЧР sвstОЦ Шr usО tСО АОХХОr
function to reduce the temperature when the
soldering equipment is not in use.
ωШКt tСО tТp аТtС sШХНОr prТШr tШ stШrКРО ТП вШu НШ
„
not intend to use the soldering iron for an
extended period of time.
χppХв sШХНОr НТrОМtХв tШ tСО sШХНОrТЧР КrОК, ЧШt tШ
„
the soldering tip.
„
Change the soldering tips using the designated
tool.
ϊШ ЧШt КppХв ЦОМСКЧТМКХ ПШrМО tШ tСО sШХНОrТЧР
„
tip.
Notice
The control units have been adapted to hold a
medium-sized soldering tip. Discrepancies may
occur if the tip is changed or a different shaped
tip is used.
An overload cut-out will also occur if the following
combinations of tools are connected: e. g.
- 2 WXHP 120 heating plates
- A WXHP 120 heating plate and desoldering iron
WXDP 120 or WXDV 120
supplied without plug.
with plug, equaliser at centre contact.
with plug
with plug and soldered resistor. Ground-
ed through selected resistor.