Werbung
Verfügbare Sprachen
Verfügbare Sprachen
5.2.2
Preparation
a) Check the power supply and the extension cable for
signs of damage or ageing before use. If a cable is
damaged during use, disconnect the mains connec-
tion cable from the mains immediately. DO NOT
TOUCH THE CABLE UNTIL IT HAS BEEN DISCON-
NECTED FROM THE MAINS. Do not use the product
if the cable is damaged or tattered.
b) Check the covers and protective devices for damage
and correct seating. Replace them if necessary.
c) Never operate the product while people, especially
children, or animals are nearby.
5.2.3
Operation
1. Always wear safety goggles.
2. Do not use the product barefoot or with sandals. Wear
sturdy footwear and long trousers.
3. Do not use the product in a thunderstorm - Danger of
lightning strike!
4. Only work in daylight or with good, artificial lighting.
5. Never operate the product with defective Protective
devices or without safety devices.
6. Do not put your hands or feet in the area of the rotat-
ing tool before or after switching on.
7. If a foreign object is hit, switch off the product immedi-
ately and remove the battery. Inspect the product for
damage and perform the required repairs before start-
ing again and working with the product. If the product
begins to experience exceptionally strong vibrations,
switch it off immediately and check it.
8. Ventilation openings must always be free.
5.2.4
Maintenance and storage
a) Disconnect the product from the power supply (i.e. re-
move the removable batteries) before carrying out
maintenance or cleaning work.
b) Do not use accessories that are not recommended
by the manufacturer. This can lead to electric shock
or fire.
c) Check the product regularly for damage.
d) Maintain and clean the product at regular intervals.
e) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the pow-
er tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of un-
trained users.
Residual risks
The product has been built according to state-of-the-
art and the recognised technical safety rules.
However, individual residual risks can arise during
operation.
• Cutting injuries.
• Damage to eyes if the stipulated eye protection is not
worn.
• Damage to hearing if the stipulated hearing protection
is not worn.
• Residual risks can be minimised if the "Safety Instruc-
tions" and the "Intended Use" together with the oper-
ating manual as a whole are observed.
• Use the product in the way that is recommended in
this operating manual. This is how to ensure that your
product provides optimum performance.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
WARNING
This power tool generates an electromagnetic field
during operation. This field can impair active or passive
medical implants under certain circumstances. In order
to prevent the risk of serious or deadly injuries, we rec-
ommend that persons with medical implants consult
with their physician and the manufacturer of the medical
implant prior to operating the power tool.
WARNING
In case of extended working periods, the operating per-
sonnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
Raynaud's syndrome is a vascular disease that causes
the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear ex-
tremely pale. The frequent use of vibrating products can
cause nerve damage in people whose circulation is im-
paired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working im-
mediately and seek medical advice.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
WARNING
Follow the safety and charging instructions
and correct usage given in the instruction
manual of your 20V IXES Series battery and
charger.
charging process and further information are
provided in this separate manual.
6
Technical data
Rated voltage
Motor speed n
Speed
Level 1
Level 2
Level 3
Thread coil cutting circle
Thread count
Cutting blade cutting circle
Number of cutting edges
www.scheppach.com
A
detailed
description
40 V (2x20V)
0
of
the
8400 rpm
4000 rpm
5000 rpm
6200 rpm
380 mm
1.6 mm
255 mm
3 pcs.
GB | 25
Werbung
