Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Flashes green 3 times.
None.
Low Battery
Flashesyelow once
"Achtung! Schwache
every 60 seconds.
Batterie. Tauschen
Batterie jetzt aus."
Flashes yel ow 2 times
"Achtung! Fehfunktion des
Fault
every 60 seconds.
Rauchsensors.
das Gerat jetzt aus."
End of Life
Flashes yel ow 3 times
"Vorsicht.
every 60 seconds.
Ende seiner Lebensdauer
erreicht. Tauschen
Gerät jetzt aus."
Technical Specifications
Power Supply
CRI 23A ithium battery (replaceable)
Battery Life
5 years (test once a
3 years (when connected to base station)
Smoke Sensor Type
Photoelectric
Operating Temperature
40 1OCJ6F ( 4.4_37.8'C)
Operating Relative Humidity
85% RH (non condensin
Alarm
Loudness
2 85 dB at 10 ft (3 m) @3.2± 0.3 kHz pu sing a arm
Silence
Duration
9 minutes
Operating Frequency
868 MHz
Maximum
Number
of
24 wireless units (only compatible with X-Sense Link
Interconnected
Units
wireless alarms)
Transmission Range
Over I,700 ft (500 m) in open air
NOTE
1.Battery life iscalculated on the current ratings in thestandbymode with weeklytestings.If its operation mode
changesto an alarming condition, the battery life will be decreased accordingly.
2. Thesmokealarm functions between40 and 1OCF(4.4 and 37.800. Prolongedexposureto temperaturesoutside
of this range can reducebattery life and affect accuracy.Wedo not recommendoperating the deviceoutside of
this range.
Exiting silence mode.
Replace the battery
immediately.
Sie die
Pleasecleanyour alarmand seeif
Tauschen
Sie
it is working normal y, f the unit
has malfunctioned, it must be
rep aced immediate y.
Der Melder
hat das
Replace the unit immediate y.
Sie das
i
Pro and Link*
• 20 •
Maintenance
To keep your smoke alarm in good working order, fol ow these simple steps:
1. Verify the unit's a arm sound and indicators are working proper y by testing the unit once a week.
2. As a minimum your smoke a arm shou d be cleaned once every 3 months: Remove the unit from the
ceiling and clean the alarm cover and vents with your vacuum cleaner fitted with the soft brush
attachment
to remove
dust
and dirt.
3. Never use detergents or other so vents to clean the unit.
4 Avoid spraying air fresheners, hair spray or other aerosols near the alarm.
5. Do not paint the unit. Paint will seal the vents and interfere with the sensor's ability to detect smoke.
6. Never attempt to disassemble the unit or clean inside. Doing so wil void your warranty.
7. When removed, place the smoke alarm back in its proper ocation as soon as possible, to assure
continuous protection from fire.
8. When household cleaning supplies or similar contaminants are used, the area should be ventilated.
Troubleshooting
Problems
Cause
The device
is not turned
e
evlce IS not tnggere
w
en
it is tested
with
smoke.
on
_
The smoke is not reaching
the sensor properly,
The time duration
insufficient
for the device
to detect
smoke.
The smoke concentration
IS low,
Solution
Make sure the battery insulating film is
removed. f the battery runs out, p ease
replacethe battery.
The smoke needs to enter the smoke sensor
from the metal mesh on the side to trigger
the device.
Continuous smoke is necessary for the device
is
to be triggered. When smokereachesthe
smoke sensor, the device will be triggered in
about 20 seconds.
Sufficient smoke concentration
is required for
the smoke alarm to detect smoke. The greater
the smoke concentration is, the faster the
alarm will respond.
•21
•
Werbung
