Connecting The Dust Extraction; Mounting The Rip Fence; Thermal Monitor; Load Indicator - Parkside Performance Pphksa 40-Li A1 Originalbetriebsanleitung

GB MT
1.­ Place­the­device­on­the­edge­of­a­table­
so that the saw blade is freely acces-
sible­or­lay­the­device­on­its­side­with­
the saw blade pointing upwards.
Removing the saw blade
2.­ Swivel­back­the­guard­cover­(19)­with­
the­pull­lever­(23)­and­place­the­tool­
on­a­level­surface.
3.­ Press­and­hold­the­spindle­lock­(12).
4.­ Loosen­the­screw­(22)­with­the­hex­key­
(5).­
5.­ Remove­the­screw­(22)and­flange­(21).
6.­ Lift­the­tool,­hold­back­the­guard­cover­
(19)­and­carefully­remove­the­saw­
blade­(20)­downwards­from­the­fixed­
guard­cover­(18).
Installing the saw blade
2.­ Swivel­back­the­guard­cover­(19)­with­
the­pull­lever­(23)­and­place­the­saw­
blade­(20)­from­below­into­the­fixed­
guard­cover­(18)­onto­the­spindle.
The marked running direction
on the saw blade (20) must cor-
respond with the marked run-
ning direction on the fixed guard cover
(18).
3.­ Place­the­flange­(21)­on­the­saw­blade­
(20).
4.­ Press­the­spindle­lock­(12)­and­fix­the­
saw­blade­(20)­with­the­screw­(22).­
Use­the­hex­key­(5).­
Make­sure­that­the­saw­blade­is­
suitable for the speed of the tool.
Connecting the dust
extraction
Connect­a­approved­dust­and­shavings­ex-
traction­directly­or­with­adapter­(14)­to­the­
chip­ejector­(25).
40
When working with materials that
produce dangerous dust, connect
the­device­to­an­appropriate,­tested­
dust­class­M­suction­device.

Mounting the rip fence

1.­ Loosen­the­wing­screw­(9)­for­the­par-
allel­guide­holder­(8)­and­insert­the­
parallel­guide­(15)­in­the­parallel­guide­
holder­(8).
2.­ Use­the­scale­(16)­on­the­parallel­guide­
(15)­and­the­recesses­in­the­base­plate­
(7)­to­gauge­the­desired­cutting­width.­
­ -­ Right­recess:­for­cutting­angle­setting­0°
­ -­ Left­recess:­for­cutting­angle­setting­45°
3.­ Tighten­the­wing­screw­(9)­of­the­paral-
lel­guide­holder­(8).

Thermal monitor

The­thermal­monitor­(30)­indicates­
when­the­device­is­in­danger­of­be-
ing­damaged.­The­device­then­switches­off­
automatically.

Load indicator

During­operation,­the­charge­level­indica-
tor­(27)­shows­the­load­on­the­device.
Tool saws at low load
->­green­LEDs­light­up
Tool saws at medium load
->­yellow­LEDs­light­up
Tool saws at high load
->­red­LEDs­light­up
Adjusting the cutting
angle
You­can­determine­the­cutting­angle­using­
the­cutting­angle­scale­(10).