Charging Time - Parkside Performance Ppsbsa 20-Li A1 Originalbetriebsanleitung

Weight (with auxiliary handle
+­smart­battery,­4 Ah) ................... 2.6 kg
Drilling capacity
for wood ........................ max. 150 mm
for masonry..................... max. 20 mm
for steel ........................... max. 16 mm
Protection category........................... IPX0
Reusable battery type ...................... Li-Ion
Temperature...........................max.­50 °C
Charging process ...................4­-­40 °C
Operation .......................... -20­-­50 °C
Storage .................................0­-­45 °C
Sound pressure level (L
Idle ....................... 85.1 dB, K
Impact drilling ........ 94.5 dB, K
Sound power level (L
Idle .......................96.1 dB, K
Impact drilling ......105.5 dB, K
Vibration (a ), Drilling
h,D
Handle ..........2.825 m/s
Auxiliary
handle ............ 2.284 m/s
Vibration (a ), Impact drilling
h,ID
Handle ........21.467 m/s
Auxiliary
handle ............19.189 m/s
For use with smart batteries
(Smart PAPS 204 A1/Smart PAPS 208 A1)
Operating frequency/
Frequency band .....2400­-­2483.5 MHz
Max. transmission power ....... ≤­20­dBm
The­specified­total­vibration­value­and­the­
stated noise emission value have been
measured according to a standardised test
method and can be used to compare one
power tool with another.
The­specified­total­vibration­value­and­the­
stated­specified­noise­emission­value­can­
also be used for a provisional assessment of
the load.
Wear ear protection.
)
pA
= 5 dB
pA
= 5 dB
pA
)
WA
= 5 dB
WA
= 5 dB
WA
2 ; K= 1.5 m/s
2 ; K= 1.5 m/s
; K= 1.5 m/s
2
; K= 1.5 m/s
2
Warning: The vibration and noise
emissions may deviate from the spe-
cified­values­during­actual­use­of­the­pow-
er tool, depending on how the power tool
is being used and, in particular, what kind
of material is being worked on.
Safety measures for the protection of the
operator are to be determined that are ba-
sed on an estimate of the actual vibration
load under the real operating conditions
(for this, all parts of the operating cycle
are to be taken into account, for example,
times in which the power tool is turned off,
and those during which it is turned on but
running without a load).

Charging time

The device is part of the (Parkside) X 20
V­TEAM­series­and­can­be­operated­with­
2
batteries­of­the­(Parkside)­X­20­V­TEAM­
2 series.
Batteries­of­the­(Parkside)­X­20­V­TEAM­
series may only be charged using chargers
2
of­the­(Parkside)­X­20­V­TEAM­series.
2
We recommend that you operate this appli-
ance with the following batteries only:
PAP 20 B1,­PAP 20 B3,­
Smart PAPS 204 A1,­Smart PAPS 208 A1
We recommend charging these batteries
with the following chargers:
PLG 20 A3,­PLG­20­A4,­PLG 20 C1,­
PLG 20 C3,­
PDSLG 20 A1,­PDSLG 20 B1,­
Smart PLGS 2012 A1
GB MT
25