Elkron IM915AM Bedienungsanleitung Seite 4

6.0 TERMINAL BOARD DESCRIPTION
TAMPER TE TC - + ALARM
JP2
JP1
JP3
MW
RANGE
Rote Led Gelbe Led
Trimmer for adjusting
microwave range
JP1 Tamper protection
ON: Tamper protection disabled
OFF: Tamper protections enabled (VdS compliant)
JP2 Enabling of leds
ON: Led disabled for function
OFF: Led enabled
JP3 Infrared range regulation
ON: range (15 m)
OFF: range (8 m)
6.0 TERMINAL BOARD DESCRIPTION
TAMPER TE TC - + ALARM
JP2
JP1
JP3
MW
RANGE
Rote Led Gelbe Led
Trimmer for adjusting
microwave range
JP1 Tamper protection
ON: Tamper protection disabled
OFF: Tamper protections enabled (VdS compliant)
JP2 Enabling of leds
ON: Led disabled for function
OFF: Led enabled
JP3 Infrared range regulation
ON: range (15 m)
OFF: range (8 m)
TAMPER NC Tamper Contact
Support terminal (Spare)
TE Walk Test Input (TE)
TC TC Input
- Supply negative
+ Supply positive
ALARM NC alarm relay contact
Support terminal (Spare)
FA Relay contacts for fault and
masking output
SYNC MW synchronous clamp
SW1
SW2
60%
80%
40%
20% 100%
TAMPER NC Tamper Contact
Support terminal (Spare)
TE Walk Test Input (TE)
TC TC Input
- Supply negative
+ Supply positive
ALARM NC alarm relay contact
Support terminal (Spare)
FA Relay contacts for fault and
masking output
SYNC MW synchronous clamp
SW1
SW2
60%
80%
40%
20%
100%
7.0 DESCRIPTION DIP-SWITCHES
1. AND/OR - TE SIGNAL SELECTION
OFF: AND operation (VdS request)
ON: OR operation
2. MEM - ALARM MEMORY FUNCTION
OFF: Latching MEMORY enable (VdS request)
ON: Latching disable
3. MW-D - MICROWAVE DELAY
OFF: Minimum delay
ON: Maximum delay
4. S/D - DUAL EDGE SIGNAL DETECTION
OFF: Single edge signal detection
ON: Dual edge signal detection
5. x1-2 - PULSE COUNT
OFF: Pulse count X 1
ON: Pulse count X 2
6. TE H/L - TE SIGNAL SELECTION
OFF: TC active low (VdS request)
ON: TC active high
7. TC-R - RELAY BLOCK FUNCTION
OFF: TC input does not blocks relay operation (VdS request)
ON: TC input blocks relay operation
8. TC H/L - TC SIGNAL SELECTION
OFF: TC active low
ON: TC active high (VdS request)
NOTE: When using CURTAIN coverage or LONG RANGE coverage, dip-
switches 4 and 5 must be OFF.
4
7.0 DESCRIPTION DIP-SWITCHES
1. AND/OR - TE SIGNAL SELECTION
OFF: AND operation (VdS request)
ON: OR operation
2. MEM - ALARM MEMORY FUNCTION
OFF: Latching MEMORY enable (VdS request)
ON: Latching disable
3. MW-D - MICROWAVE DELAY
OFF: Minimum delay
ON: Maximum delay
4. S/D - DUAL EDGE SIGNAL DETECTION
OFF: Single edge signal detection
ON: Dual edge signal detection
5. x1-2 - PULSE COUNT
OFF: Pulse count X 1
ON: Pulse count X 2
6. TE H/L - TE SIGNAL SELECTION
OFF: TC active low (VdS request)
ON: TC active high
7. TC-R - RELAY BLOCK FUNCTION
OFF: TC input does not blocks relay operation (VdS request)
ON: TC input blocks relay operation
8. TC H/L - TC SIGNAL SELECTION
OFF: TC active low
ON: TC active high (VdS request)
NOTE: When using CURTAIN coverage or LONG RANGE coverage, dip-
switches 4 and 5 must be OFF.
4
SW1
Default:
DIP1...7 = OFF
DIP8 = ON
SW1
Default:
DIP1...7 = OFF
DIP8 = ON