Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Setting the cor-
Die nachfolgend beschriebenen Tasten werden im Abschnitt
rection factors
view
A list of the correction factors for the most usual shielding gases is included in
the following chapter "Correction factors for the most usual shielding gases".
The parameter "COR" is used for setting the correction factors. The parame-
ter "COR" is in the second level of the setup menu (2nd).
If a shielding gas is used for the filler material selected other than the factory-
set shielding gas, select and set the parameter "COR" as follows:
1
2
3
The following settings are explained by the example of the operating pa-
nel "Comfort".
In the case of the operating panel "Standard":
1
2
3
4
5
6
26
G
3
4 /
i S
1
S (
a t
h
) l
G
3
4 /
i S
1
S (
a t
h
) l
Hardf. (Stahl-Auftragen)
A
S l
5 i
A (
u l
m
n i
u i
m
)
AlMg5 (Aluminium)
Al 99.5 (Aluminium)
CuAl 9 (MIG-Löten)
CuSi 3 (MIG-Löten)
CrNi 19 9 (Chrom/Nickel)
CrNi 18 8 6 (Chrom/Nickel)
Rutil (Rutil-Fülldraht)
Basic (Basischer Fülldraht)
Metal (Metall-Fülldraht)
CrNi (Chrom/Nickel-Fülldraht)
auf Seite
23
dargestellt.
Press the button(s) "material type" (1) to select a filler material for which a
different shielding gas should be used.
Press the button(s) "mode" (4) to select the process "MIG/ MAG standard
synergic welding" (11) or "MIG/MAG pulse synergic welding" (10).
This step does not apply to the operating panel "Comfort".
Press the button(s) "operating mode" (5) to select the operating mode "2step
operation" (12) or "4step operation" (13).
Enter the setup menu: keep the button "store" (2) pressed and press the but-
ton "operating mode" (5).
Select the parameters by means of the button(s) "material type" (1).
Set parameters by means of button(s) "operating mode" (5).
Open the setup menu: keep the button "store" (2) pressed and press the but-
ton(s) "process" (4).
The first parameter is shown (e.g. "GPr"). The parameter which has been
selected during a previous entry is indicated first.
Press the button(s) "process" (4) to select the parameter "2nd".
Keep the button "store" (2) pressed and press the button(s) "process" (4).
The first parameter "2nd" is shown (e.g. "PPU").
S
e t
l e
S (
a t
h
) l
-
S
e t
l e
S (
a t
h
) l
8
Hardf. (Stahl-Auftragen)
82
A
S l
5 i
A (
u l
m
n i
u i
m
)
1
AlMg5 (Aluminium)
100
Al 99.5 (Aluminium)
100
CuAl 9 (MIG-Löten)
100
CuSi 3 (MIG-Löten)
100
CrNi 19 9 (Chrom/Nickel)
97,5
CrNi 18 8 6 (Chrom/Nickel)
97,5
Rutil (Rutil-Fülldraht)
82
Basic (Basischer Fülldraht)
82
Metal (Metall-Fülldraht)
82
CrNi (Chrom/Nickel-Fülldraht)
82
1
0
0
1
2
0
2
1
8
1
5 ,
6
3
0
18
1,56
30
0
0
-
1
7 ,
6
3
0
-
1,76
30
-
1,76
30
-
1,76
30
-
1,76
30
2,5
1,68
30
2,5
1,68
30
18
1,56
30
18
1,56
30
18
1,56
30
18
1,56
30
Control panel over-
Werbung
