Noise And Vibrations Levels; Safety Pictograms; Basic Information; Use Of The Machine - Vari Rbs-700D Bedienungsanleitung


It is prohibited to work with the machine on any road of any class while the work tool is attached to the machine; the
perpendicular crossing of such roads is permissible in the places where it is specifically allowed.

Always turn OFF the engine and wait for the work tool to stop before performing any work in the close vicinity of the machine!
Before leaving the machine, always turn off the engine and secure it so that it cannot get accidentally turned on.

It is forbidden to remove any protective devices and covers from the machines.

Any repairs, adjustments, lubrication, and cleaning of the machine must be carried out when the machine is at a standstill and
its spark plug connector is disconnected.

When working with lubricants and cleaning the machine, observe the basic hygiene regulations and observe the environmental
protection regulations and laws.

2.2.2 Noise and Vibrations Levels

Description
Declared acoustic pressure emission level A at the operator's site
Declared acoustic output level A
Declared cumulative value of the acceleration of vibrations transmitted to the operator's hand-
arm 32 a
hv,d
Table 11: Measured Noise and Vibrations Levels

2.2.3 Safety Pictograms

The user is obliged to keep the pictograms on the machine in a legible state and, in case of any damage, ensure their replacement.
The position on the machine is shown in Fig. 12 on page 51 .
Position:
Sticker on the plastic cover of the working
tool - in the middle
Sticker on the plastic cover of the working
tool - on the left
Sticker on the plastic belt cover on the
right in the direction of travel.
Sticker on the plastic cover of the working
tool - on the right
Table 12: Safety Pictograms

2.3 Basic Information

2.3.1 Use of the Machine

Teh brush cutter adaptor RBS-700D
and on meadows up to maximal height of 80 cm in maintained
terrain. The brush cutter is not designed for park landscaping.

The adaptor is designed only for multifunctional carriers

The maximal vegetation height, which can be cut by the brush cutter, is limited by its composition, density and engine
power.

Due to the intended purpose of the brush cutter for the harvesting of high grass vegetations, we do not recommend
cutting vegetations with height below 40 cm. For vegetation with height below 40 cm use the mulcher adaptor
600 .

The use for purposes other than the intended purpose is; therefore, to be considered a use for an unspecified
purpose!
30 Measure according to ČSN EN 12733+A1, Annex B and ČSN EN ISO 11201:April 2010
Measured according to ČSN EN 12733+A1, Annex B and ČSN EN ISO 3744:2010
31
32 Measured according to ČSN EN 12733+A1, Annex C, par. C. 4.1.2
The brush cutter is not designed to cut any woody growth thicker than 5 mm! A failure to observe this policy will damage the machine.
33
34 The area growth must be cut and raked at least once a year!
31 (L )
WA,d
Number: Description:
1 Working tool rotation direction arrow – right (clockwise)
Caution - Before using the device, read through the operating instructions.
2
Caution - When doing maintenance on the machine, disconnect the spark plug
3
connector.
It is forbidden to place your hands or feet into the operating area of the cutting
4
tool – risk of getting cut.
5 Warning!
6 Attention, hot surface!
7 Minimum safe distance from the machine.
8 Risk of being hit by flying debris, cuttings, ejected items, etc.
9 Other persons and animals - keep a safe distance from the machine.
is designed for cutting of high thin bladed grass vegetations and wood undergrowth
30 (L )
pAd
34 areas. The areas must not feature any solid items in the growth or rough
RAPTOR Hydro
RAPTOR Hydro + RBS-700D
87.0+4.0 [dB]
103+4 [dB]
7.2+2.9 [m.s
.
RBS-700D
-2 ]
33 in forests
RMS-
19