Herunterladen Diese Seite drucken

Scheppach BC-MP380-X Originalbetriebsanleitung Seite 26

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
ATTENTION
Ensure that the cable is not squeezed during assembly.
8.1
Installation of the lower push bar
(4) (Fig. 1, 3, 4)
Note:
Make sure that the teeth mesh.
1. Attach the lower push bar (4) to the pre-fitted screws.
2. Screw down the lower push bar (4) with one washer
(4a) and one quick-clamp lever (4b) on each side. En-
sure that the cable (10), which will later be attached
with a cable clip (9), is not in the way.
3. Lock the two quick-clamp levers (4b) by pressing
them in the direction of the lower push bar (4).
They must rest against the lower push bar (4) in such
a way that they can be tightened with moderate force.
Otherwise, the quick-clamp levers (4b) must be turned
clockwise to tighten them or anti-clockwise to loosen
them.
8.1.1
Adjust the position of the lower push
bar (4) (Fig. 5)
Notes:
Three positions are possible.
Make sure that the teeth mesh.
1. Loosen the two clamping levers (4b).
2. Loosen the two clamping levers (4b) by turning them
anti-clockwise.
3. Move the lower push bar (4) to the desired position
(use the markings as a guide).
4. Close the lower push bar (4) again (see 8.1).
8.2
Installation of the upper push bar
(2) (Fig. 6, 7)
1. Screw the upper push bar (2) to the lower push bars
(4) with one flat head screw (2a), a washer (2b), a cy-
lindrical nut (2d) and a quick-clamp lever (2c) on each
side.
Two positions are possible.
2. Lock the two quick-clamp levers (2) by pressing them
in the direction of the upper push bar (2).
They must rest against the upper push bar (2) in such
a way that they can be tightened with moderate force.
Otherwise, the quick-clamp levers (2b) must be turned
clockwise to tighten them or anti-clockwise to loosen
them.
8.3
Fitting the cable holder (9) (Fig. 1,
8)
1. Clip the two cable holders (9) into the upper push bar
(2) and lower push bar (4) and secure the cable (10).
8.4
Fit the carry handle (5a) to the
grass collection basket (5) (Fig. 9)
1. Attach the carrying handle (5a) of the grass collection
bag (5) to the holder provided on the top of the grass
collection bag (5).
26 | GB
9
Operation
The battery-powered lawnmower has a cutting tool that
rotates parallel to the cutting plane. It is equipped with a
powerful and quiet-running electric motor, a robust hous-
ing, a safety bar, a safety key, a double-sided lawn edge
intake and a grass collection bag. The product's height
can also be adjusted to 6 positions and has smooth-run-
ning wheels. Please refer to the following descriptions for
the function of the controls.
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
ATTENTION
Make sure that the ambient temperature does not ex-
ceed 50°C and does not fall below -20°C during work.
ATTENTION
The product is part of the 20V IXES series and may on-
ly be operated with batteries of this series. Batteries
may only be charged with battery chargers of this se-
ries. Observe the manufacturer's instructions.
9.1
Mowing with the grass collection
basket
ATTENTION
Do not operate the product without the grass collection
basket fully attached or without a mulching insert.
ATTENTION
Only remove or attach the grass collection basket when
the engine is switched off and the blade is stationary.
9.1.1
1. Lift the discharge flap (8).
2. Lift the grass collection basket (5) by the carrying han-
dle (5a).
3. Hang the grass collection basket (5) in the grass col-
lection basket suspension provided at the rear of the
product.
4. Put down the discharge flap (8), it holds the grass col-
lection basket (5) in position.
9.1.2
The air flow generated by the blade lifts the level indica-
tor. When the grass collection basket is full, the air flow
stops. If the air flow is too low, the level indicator closes.
This is a note to empty the grass collection basket.
www.scheppach.com
Inserting the grass collection basket
(5) (Fig. 9, 13)
Level indicator (3) on the grass
collection basket (5) (Fig. 13)

Werbung

loading

Diese Anleitung auch für:

5911414900