Assembly; Operation - Scheppach 5911412917 Originalbetriebsanleitung

• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m WARNING!
The device and the packaging material are not
children's toys! Do not let children play with plas-
tic bags, films or small parts! There is a danger of
choking or suffocating!

8. Assembly

1. Remove the lawnmower and its attachments from
packaging and check that all parts are present.
2. Screw the lower push bar (5) with one wing screw
(6) on each side (Fig. 2-3).
3. Screw the upper push bar (4) to both sides of the
lower push bar (5) with one round head screw (a),
one washer (b) and one wing nut (3) each. Ensure
that the pull cord, which will be fastened later, and
the Bowden cable are not in the way (Fig. 4-5).
4. Secure the Bowden cable to the push bar with the
cable clip (c) (Fig. 7) supplied.
5. Fold up the grass collection basket (12) and snap
the plastic clips onto the frame. (Fig. 8)
6. Place the handle for the grass collection basket
(d) into the openings of the grass collection basket
(12). Then screw it from the inside with the ø4x15
screw (e).
7. Lift the discharge flap (11) with one hand and hook
in the grass collection basket (12) as shown in Fig.
9.
Hook in the grass collection basket (Fig. 9)
1. Fold the discharge flap (11) upwards.
2. Hang the grass collection basket (12) onto the
lawnmower.
Installing the rechargeable batteries (Fig.14)
1 Open the battery cover (7) and insert the re-
chargeable batteries into the battery slots.
2 Close the battery cover by folding it shut.
Note!
Only use rechargeable batteries with the same de-
gree of charge, never combine fully-charged and half-
charged batteries. Always charge both batteries at the
same time.
The battery with a weaker state of charge determines
the runtime of the device. Both batteries must always
be fully charged before operation.
9.

Operation

Safety key (Fig. 12/13)
The device can only be started if the security key (f) is
inserted in the device.
After finishing the work, this must be removed from
the device again.
Switching on the device (Fig. 6)
1. Press and hold down the switch lock (1).
2. Press the switch lever (2). The motor is running.
Switching off the device (Fig. 6)
1. Release the operating bar (2)
m Risk of injury!
The cutter bar will run on for a short time after the op-
erating bar (2) is released.
Adjusting the cutting height (Fig. 10)
Attention! The cutting height may only be adjusted
with the motor stopped and the safety key (f) removed.
Before you start mowing, check that the cutting tool is
not blunt and the fasteners are not damaged.
Replace blunt and/or damaged cutting tools to avoid
creating imbalance. During this check, switch off the
motor and remove the safety key (f).
1. Push the cutting height adjustment lever (7) out-
wards.
2. Select the desired cutting height by moving the
lever (7) to the left or right and engage the lever
(7) in one of the detents.
3. Make sure that the lever (7) engages correctly!
Remove and empty the grass collection basket
If cuttings remain on the ground, the grass collection
basket is full and should be emptied immediately.
1. Switch off the engine.
2. Wait until the cutter bar stops.
3. Lift the discharge flap (11).
4. Remove the grass collection basket (12).
www.scheppach.com GB | 35