Jacuzzi Virtus Montageanweisung Seite 34

M
AINTENANCE OF MINIMUM TEMPERATURE OF WATER IN TUB
-
AND ANTI FREEZE PROTECTION OF THE PIPES
"Smart Winter" mode lets you make use of a special probe to
monitor the temperature of the compartment under the tub, which
contains the all of the pipes of the plumbing circuit. In extreme
conditions, the system may turn on this protection (indicated on
the display by the message ICE), switching on the pump(s) and the
blower (where present).
ATTENTION: In the case of particularly low temperatures
specifically, check the electrical power supply regularly to
ensure that the function is not interrupted.
The pumps are turned on at pre-set intervals:
- temperature between 12 and 15 ° C (54 - 59 °F):
every 2 hours
- temperature between 9 and 12 ° C (48 - 54 °F):
every hour
- temperature between 6 and 9 ° C (42 - 48 °F):
every 30 minutes
- temperatures at or below 6 ° C (42 °F):
every 15 minutes
NOTES
- If the temperature of the compartment drops rapidly, the frequen-
cy of activation increases.
- If it becomes necessary to turn on the anti-freeze protection during
a filtering cycle, these will be suspended and resume when the cycle
is complete.
- If it is necessary to perform an anti-freeze cycle while a function
activated by the user is in progress, the cycle will be activated 15
minutes after the end of the function.
- If this protection is active, the spotlight may still be turned on.
"E "
NERGY SAVINGS MODE
When this function is on, the water heater only turns on again when
the temperature drops to approximately 10°C (50°F) below the set-
point.The minimum permitted temperature is 15°C.
Press the "Up/Down"
displayed.
While the LED above the thermometer symbol is on, hold
down the "Light" button for approximately 5 seconds: when
the button is released the screen briefly shows the new refer-
ence value alternated with the word "Eco"; then, the current
temperature will appear again.
To turn the function off, proceed as indicated above (press
the "Up/Down" button, etc.).
NOTE:
- To check the function status, press the "Up/Down"
"Eco" appears, the function is on.
Jacuzzi Europe S.p.A. © 2023
("S W
MART
(" " )
ECO FUNCTION
button: the current temperature is
").
Water filtering
INTER
The water needs to be filtered to keep it clean and clear. This option
is active during the day as follows:
- two filtration cycles that are repeated every 12 hours.
Each filtration cycle is has an initial phase, in which the pump
and the blower (where present) are turned on one at a time for
approximately one minute; then the cycle continues, activating
the Clearray™ Active Oxygen™ and the filtration pump for the
remaining time.
S
ETTING THE FILTERING CYCLES
To set the filtering cycle:
Hold down the "Pump"
onds: dx (where "x" indicates the duration in hours) appears on the
screen.
Use the "Up/Down"
(from a minimum of 0 to a maximum of 12 hours).
NOTE: press and hold the button until you reach the desired val-
ue; by releasing the button and pressing it again, the adjustment is
made in the opposite direction.
Press the "Pump"
confirmed, and the cycle start delay is programmed with re-
spect to the "0" time (sy parameter where "y" indicates the num-
ber of hours).
WARNING: time "0" is the instant when power is supplied to the hot
tub through the main switch or the time when the parameters are
stored; if, for example, the value "4" is set as the start delay of the
cycle, this means that the filtration will start 4 hours after turning
on the hot tub, or after storing the parameters; it is also possible to
reduce the parameter value to 0 "s": In this case, the filtration cycle
will start immediately.
Set the start delay (from a minimum of 0 to a maximum of 12)
using the "Up/Down"
"Pump"
programming mode.
When the function is active, the LED of the respective symbol
lights up (if it flashes, it means that the cycle has been suspended;
see relative section).
During the filtration cycle, the relative LED flashes.
NOTES
- If no key is touched for about 5 seconds, the device exits "parame-
ter-setting" mode.
- If there is a power outage, the data in the memory is saved, but
the time "0" will become the moment at which the electricity comes
back on. Therefore, it may be necessary to turn the main switch up
button: if the line from the hot tub off and back on to re-align the cycle start
delay with the memorized parameters.
- It is possible to vary the filtering cycle setting parameters at any
time by following the procedure provided at the beginning of this
34
button for approximately 5 sec-
button to enter the desired duration
button again and the selected value is
button and confirm the value with the
button to store the values inserted and to exit the
Jacuzzi Europe S.p.A. © 2023