Jacuzzi Virtus Montageanweisung Seite 33

Close the drain valve(s) and fill the hot tub again with fresh
water as previously explained.
Turn the omnipolar switch back on and check that the hot
tub works correctly.
Proceed with the chosen water treatment.
WARNING: read and follow all the instructions related
to the use and storage of chemical products, adhering
strictly to the manufacturer's instructions on the pack-
aging.
WARNING! Do not use trichlorine tablets! This may
damage the hot tub components and cause burning or
irritation to the skin and mucous membranes. Any use
of these chemicals voids the manufacturer's warranty.
Check and as necessary modify the water filtering cycles
based on how you intend to use the hot tub.
Installation of front and side panels
(where included)
Refer to the corresponding drawings. (
Control panel and functions
CAUTION
Only modify the parameters indicated: do not change
the configuration of the other parameters.
( 5) All hot tub functions are managed via the control panels on
the tub, as are the respective settings/programming.
NOTE Up/Down button
the key is released, the direction will reverse (when pressing the key,
the display value will decrease) and so on.
K (
EY COMBINATIONS OVAL DISPLAY
CAUTION
In the event of a malfunction, first check that these key
combinations have not been accidentally activated.
Some key combinations are used for restricted modes; it is recom-
mended not to activate these combinations, in particular:
a) by pressing the "Pump" + "Up / Down" buttons simulta-
neously for a few seconds, the normal operation of the spa may
be interrupted.
To restore operation, press and hold the indicated keys again for
a few seconds.
Jacuzzi Europe S.p.A. © 2023
2).
: hold down the key to increase; once
)
b) by pressing the "Blower" + "Up / Down" keys simulta-
neously, the display shows an alphanumeric value.
Do not press any button and wait about 10 seconds, until this
value disappears.
Setting the water temperature
The water is heated with an electrical heater or a heat exchanger.
Do not set an excessively high water temperature, i.e. over the limit
of 40 °C. The recommended temperature is 35-36 °C.
M
ODELS WITH A HEATER
tive (see relevant chapter) and, by switching on the pump, the heat-
er turns off (the led relative to the symbol
will be turned on again, if necessary, 10 seconds after the pump
itself is turned off.
W
ATER TEMPERATURE
To check or modify the water temperature, do the following:
Press the "Up/Down"
show the current saved temperature.
Press the key "Up/Down"
value from a minimum of 15 °C to a maximum of 40 °C (59÷104 °F).
NOTE:
- Press and hold the button down until you reach the desired val-
ue; by releasing the button and pressing it again, the adjustment is
made in the opposite direction.
- During operation of the heater, the light spot on the screen next to
the temperature value flashes.
To show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
To ensure precise measurement of the water temperature,
the pump is turned on at low speed (or the filtering pump,
where present), approximately every half an hour for 30 seconds
(even if filtering cycles are not set).
When the system is turned off, or there is a power outage, the last
set point is stored in memory.
When heating is in operation, the LED located under the
bol comes on (if it flashes, this means that heating has been paused,
so as not to exceed the maximum permitted consumption; see the
information at the beginning of the chapter).
CAUTION
Do not use the hot tub if the water temperature is 40 °C
or more.
33
:
if the electric consumption limit is ac-
flashes), the heater
(" ")
SET POINT
key (display B): the display will
again to change the displayed
Jacuzzi Europe S.p.A. © 2023
sym-