Panasonic WJ-AVE5 Betriebsanleitung Seite 9

39.
40.
41.
42.
43.
AA,
45.
46.
47.
48.
49.
Fade Lever (IN/OUT)
Moving this lever from OUT to IN, fade-in of the picture
takes place. Fade-out is accomplished by moving the
lever from IN to OUT.
Audio Master Level Control (MASTER, MAX/MIN)
This is the overall attenuator for the Audio Mixer.
Microphone Level Control (MIC, MAX/MIN)
This is the attenuator for the microphone signal fed to
the Microphone Input Jack (1).
Auxiliary Audio Level Control (AUX, MAX/MIN)
This is the input attenuator for the auxiliary audio signal
fed to the Auxiliary Audio Input Connectors (65) on the
rear panel.
Source Level Control (SOURCE, MAX/MIN)
This is the overall attenuator for the mixed AUDIO 1 and
AUDIO 2 sound.
Audio Control (AUDIO, 1/2)
This control is used to balance the mixed audio signal
fed to SOURCE 4 (AUDIO 1) input connector and the
signal fed to SOURCE 2 (AUDIO 2) input connector on
the rear panel.
Mix/Wipe Control (VIDEO A, B)
In the wipe mode, moving this lever from A to B will
increase the portion of the B input, and vice versa. In
the mix mode, video images are switched between A
and B.
A-bus Back Colour Selection Switch
(BACK COLOUR)
This switch is used to allocate the back colour signal
to the A-bus input. The back colour signal can be set
by the Back Colour Selection Switch (5). The LED lights
up when this switch (46) is selected.
B-bus Back Colour Selection Switch
(BACK COLOUR)
This switch is used to allocate the back colour signal
to the B-bus input. The back colour signal can be set
by the Back Colour Selection Switch (5). The LED lights
up when this switch (47) is selected.
Note:
When the B-bus Back Colour Selection Switch
(47) is selected from the B-bus Source 2 Selection
Switch (49), the LED on the B-bus Source 2
Selection Switch (49) blinks.
This blinking tells you that the Soruce 2 picture will
be selected when the B-bus Selection Switch (25)
is pressed. The same procedure will take place
when A-bus or Soruce 1 is used.
A-bus Source 2 Selection Switch (SOURCE 2)-A
This switch is used to allocate the source 2 video signal
to the A-bus input. The LED lights up when this switch
is selected.
B-bus Source 2 Selection Switch (SOURCE 2)-B
This switch is used to allocate the source 2 video signal
to the B-bus input. The LED lights up when this switch
is selected.
50.
51.
52.
53.
54.
55.
56.
A-bus Source 1 Selection Switch (SOURCE 1)-A
This switch is used to allocate the source 1 video signal
to the A-bus input. The LED lights up when this switch
is selected.
B-bus Source 1 Selection Switch (SOURCE 1)-B
This switch is used to allocate the source 1 video signal
to the B-bus input. The LED tights up when this switch
is selected.
Mix Mode Sefection Switch (MIX)
When this switch is pressed, the LED lights up, the mix
mode is selected in the MIX/WIPE EFFECT.
Wipe Mode Selection Switch (WIPE)
When this switch is pressed, the LED lights up, the
wipe mode is selected in the MIX/WIPE EFFECT. By
pressing this switch, the wipe mode will be changed
as follows:
i Normal Wipe — Border Wipe
Soft Wipe od
Note:
When the Border Wipe is selected, the colour
can be added on the border by the Back Colour
Selection Switch (5).
Joystick Positioner (POSITIONER)
The position of the wiped pattern such as circle, square
and diamond, which is selected by the Wipe Pattern
Selection Switch (6) or the Picture-In-Picture Switch
(7), can be freely set using this joystick.
Source 1 Audio Connectors
(SOURCE 1, AUDIO L/R)
—6 dBV/15 kohms audio signals for the SOURCE 1
should be supplied to these input (IN) connectors.
When the monophonic audio signal is fed to the
L-channel, this signal will be distributed to the
R-channel internally.
Source 1 Y/C Video Input Connector
(SOURCE 1, Y/C IN)
The luminance (Y) and chroma (C) signals from VTR or
colour TV should be supplied to this connector.
Note:
The Y/C input has a priority over the composite
input in circuitry.
When both the Y/C video signal and the composite
video signal are supplied to the SOURCE 1
connectors at the same time, only Y/C video signal
goes into the circuit.