Werbung
Verfügbare Sprachen
Verfügbare Sprachen
• For the safety of long hair, wear a cap or hair net.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by follow-
ing the instructions in „General safety instructions"
„Proper Use" and in the entire operating manual.
8. Attachment and operation
Before starting the equipment
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base. There are two holes
for this purpose in the machine foot. • The saw table
must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
• Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Assembly tools
1 engineer's wrench SW 10/13
8.1 Mounting the base (Fig. 2+3+3.1)
Installation parts:
• 4 stand feet (A)
• stand braces below (B): 2 x long + 2 x short
• stand braces above (C): 2 x long + 2 x short
• Mounting parts (24 hex screws M8x14, 48 washer
M8, 24 hex nuts M8); 4 hex screws M6x40, 8 wash-
er M6, 4 hex nuts M6)
Hand-tighten all screws lightly during the installation.
• Attach one stand brace below (B) each with 2
screws M8 x 16, 2 washer and 2 nuts to the stand
feet (A).
• Mount the frame struts above (C), each with 4 car-
riage bolts M8 x 14, 4 washers and 4 nuts on the
frame feet (A) as shown in Fig. 3.
• Place a cardboard box behind the machine and
then carefully tip the machine backward until the
machine rests on its housing.
• Place the previously assembled frame (Fig. 3) un-
der the base plate of the band saw; screw it into
place by hand with 4 hex bolts M6x40, 8 washers,
4 circlips and 4 hex nuts. (Fig. 3.1)
• Set the machine with the base on a level surface
and tighten all the screws and nuts firmly.
8.2 Assembling the work table (Fig. 4 - 6)
• Lay the table insert (a) in the recess in the work ta-
ble intended for this (7) (Fig. 4). (To replace, disas-
semble the work table in reverse order.)
• Place the band saw blade through the slot on the
machine table. Place the machine table on the table
guide so that the fixing screw (b) fits through the
bracket (c). (Fig. 4.1+4.2)
• Screw the machine table tight with the quick release
lever and a washer (E) (Fig. 4+5).
• Check that the bandsaw blade runs freely and does
not touch the table.
• Fit the bolt M6x40 with two washers and the nut
•
to the table. (Fig. 5.1)
• Using
the
adjustment
just
the
table
– Use a set square –
• Counter the adjustment screw (F) and tighten the
quick release lever (E).
• Set the scale pointer (G) to 0.
8.3 Fitting the table width enlargement (Fig.
7+7.1+7.2+7.3+7.4)
• Remove the two bolts and washers (d) from the table
width enlargement (6). (Fig. 7)
• Slide the table width enlargement (6) onto the table
mounted on the machine. Ensure that the clamping
lever (8) is open (Fig. 7.1+7.2).
• Push the table width enlargement fully onto the ta-
ble (Fig. 7.3) in order to fix the two bolts (d) on both
sides. (Fig. 7.4) Be sure to fit the bolts (d) on both
sides. The two bolts are used to limit the extension
of the table width enlargement.
8.4 Fitting the parallel stop (Fig. 8)
• Fit the parallel stop (5) by positioning it at the back
and fixing the clamping lever (K) in place downwards.
• When dismantling, pull the clamping lever (K) up-
wards and remove the parallel stop (5).
• The clamping force of the parallel stop can be ad-
justed at the rear knurled nut (P).
8.5 Adjusting the cutting width (Fig. 8+8.1)
• The parallel stop (5) must be used when cutting sec-
tions of wood lengthways.
• Place the parallel stop (5) on the guide rail (Q) to the
left or right of the sawing blade
• 2 scales (L/M) are printed on the guide rail for the
parallel stop (5), which show the distance between
the stop rail and sawing blade.
• Adjust the parallel stop (5) to the required dimension
in the window (O) and use the clamping lever (8) to
fix in place for the parallel stop. (Fig. 8)
8.6 Using the table width enlargement (Fig. 9-10)
• Always use the table width enlargement (6) with par-
ticularly wide workpieces.
• Loosen the clamping lever (8) and pull the table width
enlargement out far enough so that the workpiece to
be sawn can lie on it without tipping. (Fig. 10)
8.7 Sawblade changing(Fig. 11+12)
• Attention: Pull the mains plug! Attention! Wear protec-
tive gloves when changing the saw blade! Risk of injury!
screw
(F)
to
ad-
to
a
right-angle.
GB
27
Werbung
