Werbung
Verfügbare Sprachen
Verfügbare Sprachen
40.
41.
42.
43.
44.
45.
46.
47.
Mix/Wipe Mode Selection Switches (MIX/WIPE)
These two switches are used to select the Mix or Wipe
mode.
A-bus Input Selection Switches
These switches are used to select the allocation of
video signal to the A-bus input.
VIDEO 1:
The video signal fed to either the
SOURCE
1@
and @ or SOURCE 2
6 and
@
connector
on
the
rear
panel, as selected by the Input Mode
Selection switches © and the digi-
tal frame synchronizer, is selected.
The video signal fed to either the
SOURCE
1
and @ or SOURCE 2
@ and @
connector
on the rear
panel, as selected by the Input Mode
Selection switches ©, is selected.
The background colour signal set by
the Back Colour Selection switch @
is selected.
he
VIDEO 2:
BACK COLOUR:
B-bus Input Selection Switches
( B VIDEO
1/VIDEO 2/BACK COLOUR)
These switches are used to select the allocation of the
video signal to the B-bus input in addition to the A-bus
Input Selection switches @ .
Mix/Wipe Lever ([Al, [B])
In the wipe mode, moving this lever from A to B will
increase the portion of the B input, and vice versa.
In the mix mode, video images are switched between A
and B.
Auto-Take Start Switch (AUTO TAKE) and
Speed Control (SPEED)
Turning this control, the speed of auto-take effect can
be freely adjusted from approx. 0.2 to 2 seconds.
Press the Auto-Take Start Switch (AUTO TAKE) to start
the auto-take function.
Balance Control (BALANCE, AUDIO 1/AUDIO 2)
This control is used to balance the mixed audio signal
fed to SOURCE
1 (AUDIO 1) input connector and the
signal fed to SOURCE 2 (AUDIO 2) input connector on
the rear panel.
Audio level Control (AUDIO, MAX/MIN)
This is the overall attenuator for the mixed AUDIO 1 and
AUDIO 2 sound.
Auxiliary Audio Level Control (AUX, MAX/MIN)
This is the input attenuator for the auxiliary audio signal
fed to the AUX AUDIO
IN connectors @ on the rear
panel.
48.
49.
50.
51.
52.
53.
PoC
CIDE _| TITLE [| AUDIO |
N
VIDEO & TITLE &
AUDIO fade
Microphone Level Control (MIC, MAX/MIN)
This is the input attenuator for the microphone signal
fed to the MIC input jack ®.
Fade Lever (IN/OUT)
Moving this lever from OUT to IN, fade-in of the sound
takes place. Fade-out is accomplished by moving the
lever from IN to OUT.
Fade Control Switches (VIDEO, TITLE, AUDIO)
These switches are used to select the fade mode as fol-
lows.
ON
OFF
OFF
N
OFF
ON
O
ON
ON
ON
Automatic Fade Control Switch
(AUTO FADE)
This switch
is used
to perform
automatically
the
fade-in and out functions.
When the Fade Lever @ is positioned at slightly upper
from its center position, the fade in function is auto-
matically performed.
When the fade Lever @ is positioned at slightly under
from its center position, the fade-out function is auto-
matically performed.
Colour Selection Switches (COLOUR SELECT,
BACK COLOUR/WHITE/BLACK)
These switches are used to select the colour for the
fade-out mode as follows.
BACK COLOUR:
The back colour signal set by the
Back Colour Selection switch 8 is
selected.
The image will fade out in white.
The image will fade out in black.
WHITE:
BLACK:
Source 1 Video Connectors
(SOURCE 1, VIDEO IN/OUT)
A 1.0 Vp-p/75 ohm composite video signal should be
supplied to the input (IN) connector. Connecting coaxial
cables with BNC connectors to the output (OUT) con-
nector, the high impedance video loop is automatically
selected. At all other times, the terminals are automati-
cally terminated by 75 ohms.
Werbung
