Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Note:
(1) If the input video signal does not meet with the PAL
colour standard or the CCIR B/W standard video
signal, this could cause a disturbance of synchroni-
zation.
(2) In case the S/N ratio of the input signal is very low,
this may be reflected in a low- quality picture.
(3) If the input video signal is very jittery, such as in case
of the VTR playback picture, this could cause a dis-
turbance of synchronization or colour.
In case the video signal from the VTR and that of the
camera is to be mixed, itis recomended to select the
camera signal for the VIDEO 2 signal by the Input
Mode Selection switches ©.
54. Source
1 S-VHS Video Input Connector
(SOURCE
1, Y/C IN)
The luminance (Y) and chroma (C) signals from S-VHS
VTR or colour TV are supplied to this connector.
55. Source
1 Y/C-Composite Selection Switch
(SOURCE
1, Y/C-COMP)
This switch selects either Y/C or composite signal to
be supplied to source
1.
56. Source 2 Video Connectors
(SOURCE 2, VIDEO IN/OUT)
The IN connector accepts a 1.0 Vp-p/75 ohm composite
video signal.
Connecting coaxial cable with a BNC connector to the
OUT connector, the high impedance video loop is auto-
matically selected. At all other times, the terminals are
automatically terminated by 75 ohms.
Note:
(1) If the input video signal does not meet the PAL
colour standard or the CCIR
B/W standard, this
could cause synchronization error.
(2) In case the S/N ratio of the input signal is very low,
this may be reflected in a low-quality picture.
(3) If the input video signal is very jittery, such as a
picture played back on a VTR, synchronization or co-
lour error may appear.
In case the video signal from the VTR and that of the
camera is to be mixed, itis recomended to select the
camera signal for the VIDEO 2 signal by the Input
Mode Selection switches ®.
57. Source 2 S-VHS Video Input Connector
(SOURCE
2, Y/C IN)
The luminance (Y) and chroma (C) signals from S-VHS
VTR or colour TV are supplied to this connector.
58. Source 2 Y/C-Composite Selection Switch
(SOURCE
2, Y/C-COMP)
This switch selects either Y/C or composite signal to
be supplied to source 2.
59. External Camera Input Connector
60.
61.
62.
63.
64.
65.
66.
(EXT CAMERA
IN)
For the key signal in the superimpose mode, this con-
nector accepts a 1.0 Vp-p/75 ohm composite video
signal, which is synchronized with the sync output sig-
nal provided at the SYNC OUT connector @ .
Sync Output Connector (SYNC OUT)
A 1.0 Vp-p/75 ohm negative polarity composite sync
signal is provided at this connector for synchronization
of an external camera.
Recording Video Output Connectors
(REC VIDEO OUT
1/2)
A 1.0 Vp-p/75 ohm composite video signal, as select-
ed by the Recording Video Output Selector switches
@, is provided at these connectors.
Y/C REC Video Output Connector
The luminance (Y) and chroma (C) signals are obtained
from these connectors
1 and 2 when composite or Y/C
signal is supplied to source
1 or 2.
Preview Output Connector (PREVIEW OUT)
A 1.0 Vp-p/75 ohm composite video signal of the EF-
FECT (all effect) image is provided at this connector.
Source 1 Audio Connectors
(SOURCE 1, AUDIO L/R)
—10 dBV/15 kohms audio signals for the SOURCE
1
should be supplied to these input (IN) connectors. The
input audio signals can be taken out from the output
(OUT) connectors with a high impedance loop.
SOURCE
2 Audio Connectors
(SOURCE
2, AUDIO
L/R)
The IN connectors accepts a —10 dBV/15 kohms au-
dio signal.
The input audio signals can be taken out from the out-
put (OUT) connectors with a high impedance loop.
Recording Audio Output Connectors
-8 dBV/1
kohms audio signals for recording are sup-
plied at these connectors.
Werbung
