Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1;
2;
2
Caution:
4.
o1
eo
:
Be
Power Indicator (POWER)
Sync Warning Indicator (SYNC WARNING)
This
LED
indicator
shows
the
sync
conditions
as
follows.
Green:
The GEN-LOCK sync mode is selected and
the sync generator inside the unit is syn-
chronizing the signal with the VIDEO 2 signal.
The Internal sync mode is selected and no
video signal is supplied to the VIDEO 2 chan-
nel.
The synchronization is disturbed or unstable.
Even if the VIDEO 2 signal is supplied, the
sync generator inside cannot synchronize the
signal properly because of noise in the VIDEO
2 signal.
If the
indicator
colour
of the
indicator
changes, check the SOURCE signal for the
VIDEO 2 signal whether the synchronization
error still exists.
Orange
(amber):
Red:
Note:
Input Mode Selection Switches (INPUT MODE)
These 4 switches are used to select the input mode as
follows:
SOURCE 1
VIDEO IN. —*<1o=pqy——
2c—_p2
SOURCE 2
ie
VIDEO IN
The SOURCE 1 video signal is used for the VIDEO
* 1 signal, being passed through the digital frame
synchronizer, and the SOURCE 2 video signal is
used for the VIDEO 2 signal.
. The SOURCE 1 video signal is used for the VIDEO
2 signal and the SOURCE 2 video signal is used
for the VIDEO 1 signal, the latter being passed
through the digital frame synchronizer.
. The SOURCE 1 video signal is used for both
" the VIDEO 1 and VIDEO 2 signal.
: The SOURCE 2 video signal is used for both the
VIDEO 1 and VIDEO 2 signal.
VIDEO 1
VIDEO 2
Do not change the setting of these switches
during recording, as this may result in synchroni-
zation error.
Memory Switches (MEMORY
1, 2, 3, 4)
This switch is used to memorize the program or per-
form the programmable functions.
. Mode Selection Switch (PRG/RUN)
This switch is used for the programmable functions.
PRG:
By pressing the MEMORY switch ©, four kinds
of programs can be memorized.
RUN:
This position is ready to perform the automat-
ic Effect operation.
6. Run Speed Control (RUN SPEED)
10.
11.
12.
13.
14.
Turning this control, the speed of memory
effect can
be freely adjusted from approx. 0.05 to 1 second.
. Wipe Pattern Selection Switches
(WIPE PATTERN)
The wipe pattern can be selected as follows.
WIPE PATTERN
De WJeGCeaBeae
Oo
o}oO
oie}e
[O
ie jo)
je)
lo}
[oO
ar
|=
Oo
(=)
O
O
°
iS)
oO
| Jol
O
lolol
Through combined
use of the four switches on the
right, the following wipe patterns can
be selected.
Please note that positioning in this case is not effec-
tive by moving of the Joystick Positioner
@.
. Wipe Pattern Selection Switches (POSITIONER)
These two switches are used to permit the wipe at
desired position.
Position of square and circle wipe in this case is done
through use of the Joystick Positioner
@.
. Audio Level Indicator (AUDIO LEVEL)
These LED indicators show the output level for the left
and right channels, respectively.
Power ON/OFF Switch (POWER ON/OFF)
Headphone Level Control (LEVEL,MIN/MAX)
This is level control for headphone output.
Headphone Jack (PHONES)
This jack is used to connect a headphone and the out-
put level can be adjusted by the Headphone Level Con-
trol ©.
Microphone Input Jack (MIC)
This jack is used to connect a microphone with a tip-
ring-sleeve or tip-sleeve type phone plug.
Title Input Connector (TITLE)
This connector is used to connect the optional Charac-
ter Generator WV-KB12.
@:
Character IN
®
@:
Not used
a
oS
@®:
Ground
=
©
@:
Not used
are
Os @®
@®:
Sync out
©:
Not used
Front View
@:
Ground
®:
+9V OUT
®©:
Ground
@:
Not used
Werbung
