Scheppach 5901313901 Original Bedienungsanleitung Seite 32

Hexagon screws must each be inserted from outside
inwards, and the connections must be secured from
the inside with nuts. During assembly nuts and screws
must only be tightened until hand-tight, so that they
cannot fall out. If you tighten the nuts and screws fully
before final assembly, the circular table saw cannot
be erected in a correct and stable manner.
8.1 Assembling the frame and table width extend-
er (Fig. 4-10)
1. Turn the table circular saw over and place it on
the floor.
2. Loosely tighten the table width extender (6) on the
saw table (1) using the hexagon bolts (a), washer
(c), spring washer (d) and nuts (e). (Fig. 6)
3. Screw the four legs (19) and the table supports (24)
onto the housing. (Fig. 7)
4. Loosely tighten the table supports (24) on the
table width extender (6) using hexagon bolts (a),
washer (c), spring washer (d) and nuts (e). Loose-
ly tighten the four legs (19) and table supports (24)
onto the housing using the hexagonal bolts (a).
5. Now loosely screw the four central struts (20a,20b)
with the legs (19) using the carriage bolts (b),
washer (c), spring washer (d) and nuts (e). (Fig. 8)
6. Screw the stand brackets (22) to the holes in the
rear stand legs (19). Assembly material: 2 car-
riage bolts (b), washers (c), spring washers (d)
and nuts (e). (Fig. 9)
7. ATTENTION: Both stand brackets (22) must be
attached to the rear of the machine at the fixing
points (23). (Fig. 9)
8. Align the table width and length extension lush
with the saw table.
9. Next, tighten all the screws of the legs (19) and
the table width extender (6).
10. Now attach the rubber feet (21) to the legs (19)
(Fig. 10).
11. Place the table circular saw on the base frame (11).
8.2 Insert guide rail (Fig. 11+12)
1. Mount the carriage bolts (b) in the holes provided
in the worktable and the table extensions (6) by
securing them from behind with the flange nuts (e).
2. Loosely tighten the flange nuts (e).
3. Connect both guide rails (15, 15a).
4. Slide the connected reails over the guide groove
on the back over the carriage bolts (b) until they
are centred on the table surface.
8.3 Aligning the guide rail (Fig. 11+12)
1. Turn the saw blade out of the sawing table at
maximum by turning the crank (10) clockwise as
far as it will go.
2. Position the rip fence (14) with the cam lever (13)
open on the guide rails (15) on the sawing table
and fix it in the 0-position by pushing the cam
lever (13) down completely.
32 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
3. Slide the connected guide rails to the left until the
rip fence is at the outer right side of the saw blade.
Then tighten the flange nuts (e) to fix this setting.
4.
5. No fit the end caps (15b) on both sides of the rail.
8.4 Mounting / dismounting the Saw Blade
Guard (Fig. 13 + 14)
1. Loosen the screw with nut and washer (27)of the
saw blade guard (2). Place the saw blade guard
(2) from the top onto the riving knife (3).
2. Mount the screw with nut and washer (27) so that
the bolt sits firmly in the slot.
3. Do not overtighten the bolt (27) The saw blade
guard must be able to move freely.
4. Dismantling is carried out in reverse order.
m CAUTION: Before you start sawing, the saw balde
guard (2) has to be lowered onto the item being sawn.
After fitting, check that the saw blade guard (2) is
functioning properly. Lift the saw blade guard and
then release it. The saw blade guard should automat-
ically move back to its starting position.
8.5 Mounting / adjusting the riving knife;
Caution! Remove the mains plug! The setting of
the saw blade (4) must be checked whenever a
blade has been replaced.
1. Adjust the saw blade (4) to a max. cutting depth,
move to the 0° position and lock in place.
2. Dismantle the saw blade guard (2) (not during in-
itial assembly).
3. Release the two countersunk screws of the table
insert (25) and remove the table insert (5).
4. Loosen the fixing srew of the riving knife (26). (use
the open-ended spanner AF8 supplied).
5. Push the riving knife (3) upwards.
6. The distance between the saw blade (4) and riv-
ing knife (3) should be between 3 mm and max. 5
mm, (Figure. 18)
7. Retighten the fixing screw of the riving knife (26)
and mount the table insert (5).
8. Mount the saw blade guard (2) with the screw and
knurled nut and washer (27).
8.6 Connect the suction device (Fig. 2)
1. Attach a suction hose to the suction adapter (16).
If necessary, secure the suction hose with a hose
clamp to prevent it from slipping off the suction
adapter (16).
2. A household vacuum cleaner is not suitable as
a suction device. Use a multi-purpose vacuum
cleaner or a swarf extraction machine.