Scheppach 5901313901 Original Bedienungsanleitung Seite 34

CAUTION: Do not push the stop rail (30) too far in
the direction of the saw blade. The distance between
the stop rail (30) and saw blade (4) should be approx-
imately 2 cm.
9.6 Adjusting the scale of the parallel stop (Fig. 23)
Check whether the display on the sight glass (32) of
the parallel stop (14) shows the correct values with re-
spect to the cutting line. If this is not the case, please
proceed as follows:
1. Release the screw (32a) with which the display
on the sight glass (32) of the parallel stop (14) is
attached. The sight glass (32) display can now be
set to the correct position.
2. Now, retighten screw (32a) on the sight glass (32).
10. Usage
10.1 Working instructions
• After each new adjustment, we recommend a trial
cut in order to check the set dimensions.
• After the saw has been switched on, wait until the
saw blade has reached its maximum speed before
you carry out the cut.
• Secure long workpieces against tilting at the end of
the cutting process (e.g. unwinding stand etc.)
• Caution with incision cutting.
• Operate the device only with a suction system.
• Check and clean the suction channels regularly.
10.2 Suitability of the saw blades
• 24 teeth: high chip removal, rough cut image
• 48 teeth (not included in the scope of delivery):
hard materials, lower chip removal, iner cut image
10.3 Performing longitudinal cuts (Fig. 24)
Here, a workpiece is cut in its longitudinal direction.
One edge of the workpiece is pressed against the par-
allel stop (14) while the lat side lies on the saw table (1).
The saw blade guard (2) must always be lowered onto
the workpiece. The working position during longitu-
dinal cutting must never be in a straight line with the
cutting line.
1. Adjust the parallel stop (14) and stop rail (30) accord-
ing to the workpiese height and the desired width.
2. Switch on the saw.
3. Place your hands with the fingers closed togeth-
er flat on the workpiece and push the workpiese
along the stop rail (30) into the saw blade (4).
4. Guide from the side with your left or right hand (de-
pending on the position of the parallel stop) only up
to the front edge of the saw blade guard (2).
5. Always push the workpiece through to the end of
the riving knife (3).
6. The cutting waste remains on the saw table (1) un-
til the saw blade (4) is back in its resting position.
7. Secure long workpieces against tilting at the end
of the cutting process! (e.g. unwinding stand etc.)
34 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
ATTENTION: The parallel stop must be set parallel
with the saw blade. Check the alignment and firm
seating of the rip fence (14), especially during use
and when not in use for long periods Vibrations can
cause screw connections to loosen. If necessary, re-
adjust the rip fence (14) and retighten the knurled nut
(i). Secure the screw connections (k) with the Allen
wrench (not supplied) (Fig. 21a).
10.3.1 Cutting narrow workpieces (Fig. 25)
Longitudinal cuts of workpieces with a width of less
than 120 mm always have to be cut with the help of a
push stick (17). The push stick (17) is included in the
scope of delivery. Replace a worn or damaged push
stick (17) immediately.
1. Adjust the parallel stop (14) according to the
planned workpiece width.
2. Advance the workpiece with both hands, making
sure that you use a push stick (17) as a pushing
aid in the vicinity of the saw blade.
3. Always push the workpiece through to the end of
the riving knife.
m CAUTION: In the case of short workpieces, the
push stick should be used from the beginning of the
cutting process.
10.3.2 Cutting very narrow workpieces
For longitudinal cuts of very narrow workpieces with a
width of 30 mm and less, a push block must be used
without fail. There is no push block included in the
scope of delivery! (Available from specialist shops)
Replace a worn push block as soon as possible.
During sawing, workpieces can become jammed be-
tween the parallel stop and the saw blade, caught by
the saw blade and then ejected at speed. For this rea-
son, the lower guide surface of the parallel stop should
be favoured. Shift the stop rail if required (see 9.4.2).
1. The parallel stop should be adjusted to the cutting
width of the workpiece.
2. Press the workpiece with the push block against
the stop rail and push the workpiece with the push
stick (17) through to the end of the riving knife (3).
10.3.3 Performing bevel cuts (Fig. 26)
All bevel cuts are made using the parallel stop (14).
The parallel stop (14) must always be fitted to the right
of the saw blade. Otherwise, workpieces can become
jammed between the parallel stop and the saw blade
during sawing and ejected at speed.
1. Adjust the saw blade to the desired angle.
2. Adjust the parallel stop (14) according to the work-
piece width and height.
3. Perform the cut according to the workpiece width