Additional Safety Instructions - Parkside PVKO 50 B2 Originalbetriebsanleitung

d. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in the
hands of untrained users. Unused electric tools should be
stored in a dry, elevated or closed location out of the reach
of children.
e. Maintain power tools and accessories. Check
whether moving parts function properly and
do not get stuck and whether parts are bro-
ken or are damaged and thus adversely affect
the electric tool function. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
h. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and con-
trol of the tool in unexpected situations.
Service
a. Only have your electric tool repaired by quali-
fied specialists and only with original spare
parts. This ensures that safety of the electric tool is main-
tained.
Safety instructions for compressors
m Attention!
The following basic safety measures must be observed when
using this compressor for protection against electric shock, and
the risk of injury and fire.
Read and observe these instructions before using the device.
Safe work.
1. Take care of your tools
- Keep your compressor clean so that you can work well
and safely.
- Follow the maintenance instructions.
- Check the connection cable of the electric tool regularly
and have it replaced by a recognised specialist when
damaged.
- Check extension cables regularly and replace them when
damaged.
2. Pull the connector out of the socket
- When the electric tool is not in use or prior to maintenance
and when replacing tools such as saw blades, bits, milling
heads.
3. Check the electric tool for potential damage
- Protective devices or other parts with minor damage must
be carefully inspected to ensure that they function correctly
and as intended prior to continued use of the electric tool.
18 GB
- Check whether the moving parts function faultlessly and
do not jam or whether parts are damaged. All parts must
be correctly mounted and all conditions must be fulfilled to
ensure fault-free operation of the electric tool.
- Damaged protective devices and parts must be properly
repaired or replaced by a recognised workshop, insofar
as nothing different is specified in the operating manual.
- Do not use any faulty or damaged connection cables.
4. Attention!
- For your own safety, only use accessories and additional
equipment that are indicated in the operating manual or
have been recommended or indicated by the manufac-
turer. Use of other tools or accessories that those recom-
mended in the operating manual or in the catalogue could
represent a personal danger to you.
5. Replacing the connection line
- If the power tool's supply cord is damaged it must be re-
placed with a specially prepared and approved supply
cord available from Customer Service.
6. Filling tyres
- Check the tyre pressure immediately after filling using a
suitable pressure gauge, e.g. at a petrol station.
7. Street-legal compressors in construction site operation
- Ensure that all hoses and fixtures are suitable for the maxi-
mum permissible working pressure of the compressor.
8. Set-up location
- Only set up the compressor on a flat surface.
- Starting the motor is forbidden if the temperature is below
0°C.
- Do not touch the hot components of the compressor.
- It is recommended to equip the feed hoses with a safety
cable in cases where the pressure is above 7 bar, e.g.
using a wire cable.
- Avoid over-stressing the piping system by using flexible
hose connections to prevent kinking.
- Do not tilt the compressor more than 30° from the vertical.

Additional safety instructions

Do not operate the compressor in the rain.
When used in combination with spraying accessories (e.g.
paint spray gun), keep the spray equipment away from the
device when filling and do not spray towards the compressor.
Observe the corresponding operating manuals of
the respective compressed air tools / compressed
air attachments!
The following general instructions must also be observed:
Safety instructions for working with compressed
air and air blow guns
• Ensure there is sufficient distance to the product, at least
2.50 m, and keep the compressed air tools / compressed
air attachments away from the compressor during operation.
• Compressor pump and lines reach high temperatures during
operation. Touching them will cause burns.
• The air drawn in by the compressor must be kept free of
impurities that can cause fires or explosions in the compres-
sor pump.