Scheppach FS3600 Original Bedienungsanleitung Seite 25

Attention! The FS4700 Tile Cutter may only be op-
erated with the 10 mA PRCD (residual current circuit
breaker) installed at the factory.
• Wearing personal protective equipment is essential
for all work with the machine.
• Always wear protective goggles to avoid eye inju-
ries.
• Be sure to wear a hair net or a suitable work cap if
your hair is long enough.
• Wear tight-fitting work clothing. The rotating tool
could catch sleeves or the like.
• Never remove chips or dust with your bare hands.
• When the machine is switched off, it is best to re-
move chips or dust with a hand brush or paintbrush.
• Check that the protective devices function correctly
before starting work.
• Do not overload the machine, they work better and
safer in the specified power range.
• Use the correct tool and make sure that the tools
(cutting wheel) are not blunt or damaged in any way.
• Always lead the cable backwards away from the
machine. Protect any cables from heat, oil and
sharp edges.
• Unplug the mains plug during repairs and mainte-
nance and when machine not in use.
• Work on electrical equipment may only be carried
out by a qualified electrician. Only original parts
may be used.
• Clean workstations make it easier to work.
• Pay attention to what you are doing. Remain sensi-
ble when working.
• Make sure that the substructure can support the
weight of the machine and is sufficiently stable. It
must be ensured that no vibrations can occur during
work.
• To protect against corrosion, all bare parts of the
machine are heavily greased at the factory. Clean
the machine with a suitable environmentally friendly
cleaning agent before commissioning.
• The machine must not be used to machine mate-
rials that are hazardous to health or that generate
dust, e.g. wood, Teflon etc.
• Do not use the machine in the vicinity of combus-
tible fluids or gases.
• Only use the machine in suitable rooms and do not
expose the machine to moisture or humidity.
• Always ensure good lighting when working.
• Do not use the mains cable to pull the connector out
of the socket.
• Always use sharp and clean tools.
• In the event of dangerous situations or technical
faults, switch off the machine immediately and dis-
connect the mains plug.
• In case of damage, do not continue working with the
machine and disconnect the mains plug.
• Only tool attachments and accessories approved by
the manufacturer may be used. The use of non-ap-
proved parts poses a considerable danger of injury.
• Always keep the work area clean and orderly. Dirt
and disorder in the work area can cause accidents.
• Always wear protective goggles when working with
the machine. A face mask or dust mask must also
be used when working with a lot of dust.
• Chuck key and other tools must be removed before
switching on the machine.
• Place the machine on a level, non-slip floor. The
machine must not wobble.
• Make sure that the voltage on the data plate match-
es the existing voltage. Then connect the connector
to the mains.
• Put on protective goggles.
• Wear hearing protection.
• Wear protective gloves.
• Do not use cracked diamond cutting wheels and re-
place them.
• Attention! Cutting wheel runs on!
• Do not brake the diamond cutting wheel by applying
lateral pressure.
• Attention! The diamond cutting wheel must always
be cooled with water.
• Pull out the mains plug before changing the cutting
wheel.
• Only use suitable diamond cutting wheels.
• Never leave the machine unattended in rooms with
children.
• Disconnect the mains plug before checking the mo-
tor compartment electrical system.
• Direction of rotation of the cutting wheel: Check the
direction of the arrow on the cutting wheel, the di-
rection of the arrow must match with the direction of
rotation of the motor shaft.
• Keep you hands, fingers and arms away from the
rotating cutting wheel. Always maintain sufficient
clearance from the diamond cutting wheel.
• Only use diamond cutting wheels recommended by
the manufacturer which conform to EN 13236. The
use of any type of saw blades is prohibited.
• Only use cutting wheels whose speed is at least
3000 rpm.
• The cutting of metal and wood is not permitted.
www.scheppach.com GB | 25